Ingersoll Rand Q2 Serie Manual De Instalación

Series QP and QS Drills and Chuck Guard Kits are designed for drilling operations in the
aerospace, automotive, appliance, electronic, machining and furniture industries.
Ingersoll- -Rand is not responsible for customer modification of tools or accessory kits for
applications on which Ingersoll- -Rand was not consulted.
READ THIS MANUAL BEFORE OPERATING THE TOOL AND INSTALLING
THE CHUCK GUARD KIT. IT IS THE RESPONSIBILITY OF THE EMPLOYER
TO PLACE THE INFORMATION IN THIS MANUAL INTO THE HANDS
OF THE OPERATOR. FAILURE TO OBSERVE THE FOLLOWING
Always operate, inspect and maintain this tool in
•
accordance with all regulations (local, state, federal
and country), that may apply to hand held/hand
operated pneumatic tools.
For safety, top performance, and maximum
•
durability of parts, operate this tool at 90 psig
(6.2 bar/620 kPa) maximum air pressure at the inlet.
Always turn off the air supply and disconnect the
•
air supply hose before installing, removing or
adjusting any accessory on this tool, or before
performing any maintenance on this tool.
Always wear eye protection when operating or
•
performing maintenance on this tool.
Always wear hearing protection when operating
•
this tool.
Keep hands, loose clothing, long hair and jewelry
•
away from working end of tool.
Keep body stance balanced and firm. Do not
•
overreach when operating this tool. Anticipate and be
alert for sudden changes in motion, reaction torques,
or forces during start- -up and operation.
Tool accessories may continue to rotate briefly after
•
throttle is released.
Air powered tools can vibrate in use. Vibration,
•
repetitive motions or uncomfortable positions may
be harmful to your hands and arms. Stop using any
tool if discomfort, tingling feeling or pain occurs.
Seek medical advice before resuming use.
Use accessories recommended by Ingersoll- -Rand.
•
This tool is not designed for working in explosive
•
atmospheres.
This tool is not insulated against electric shock.
•
Do not carry or drag the tool by the cord or cable.
•
The use of other than genuine Ingersoll- -Rand replacement parts may result in safety hazards, decreased tool
performance, and increased maintenance, and may invalidate all warranties.
Repairs should be made only by authorized trained personnel. Consult your nearest Ingersoll- -Rand Authorized
Servicenter.
Refer All Communications to the Nearest
Ingersoll- -Rand Office or Distributor.
 Ingersoll- -Rand Company, 2001
Printed in U.S.A.
INSTALLATION MANUAL
1/4" AND 3/8" CHUCK GUARD KITS
FOR Q2 SERIES QP AND QS DRILLS
IMPORTANT SAFETY INFORMATION ENCLOSED.
WARNINGS COULD RESULT IN INJURY.
PLACING TOOL IN SERVICE
USING THE TOOL
FOR
Do not use damaged, frayed or deteriorated
•
hoses and fittings.
Always use clean, dry air at 90 psig
•
(6.2 bar/620 kPa) maximum air pressure. Dust,
corrosive fumes and/or excessive moisture can ruin
the motor of an air tool.
Do not lubricate tools with flammable or volatile
•
liquids such as kerosene, diesel or jet fuel.
Do not remove any labels. Replace any damaged
•
label.
Note the position of the reversing mechanism before
•
operating the tool so as to be aware of the direction of
rotation when operating the throttle.
Prevent exposure and breathing of harmful dust and
•
particles created by power tool use:
Some dust created by power sanding, sawing,
grinding, drilling and other construction activities
contains chemicals known to cause cancer, birth
defects or other reproductive harm. Some
examples of these chemicals are:
- - lead from lead based paints,
- - crystalline silica from bricks and cement and
other masonry products, and
- - arsenic and chromium from chemically
treated lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic
particles.
04577920
Form P7512
Edition 2
November, 2001
F
E
P