Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 13

Enlaces rápidos

Models 7803 and 7803- - EU Drills are designed for drilling, honing, reaming and hole
sawing.
Ingersoll- -Rand is not responsible for customer modification of tools for applications
on which Ingersoll- - Rand was not consulted.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THE INFORMATION
IN THIS MANUAL INTO THE HANDS OF THE OPERATOR.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
PLACING TOOL IN SERVICE
Always operate, inspect and maintain this tool in
accordance with all regulations (local, state,
federal and country), that may apply to hand
held/hand operated pneumatic tools.
For safety, top performance, and maximum
durability of parts, operate this tool at 90 psig
(6.2 bar/620 kPa) maximum air pressure at the
inlet with 3/8" (10 mm) inside diameter air supply
hose.
Always turn off the air supply and disconnect the
air supply hose before installing, removing or
adjusting any accessory on this tool, or before
performing any maintenance on this tool.
Do not use damaged, frayed or deteriorated air
hoses and fittings.
Be sure all hoses and fittings are the correct size
and are tightly secured. See Dwg. TPD905- - 1 for a
typical piping arrangement.
Keep clear of whipping air hoses. Shut off the
compressed air before approaching a whipping air
hose.
Always use clean, dry air at 90 psig maximum air
pressure. Dust, corrosive fumes and/or excessive
moisture can ruin the motor of an air tool.
Do not lubricate tools with flammable or volatile
liquids such as kerosene, diesel or jet fuel.
Do not remove any labels. Replace any damaged
label.
USING THE TOOL
Always wear eye protection when operating or
performing maintenance on this tool.
Always wear hearing protection when operating
this tool.
The use of other than genuine Ingersoll- - Rand replacement parts may result in safety hazards, decreased tool
performance, and increased maintenance, and may invalidate all warranties.
Repairs should be made only by authorized trained personnel. Consult your nearest Ingersoll- - Rand Authorized
Servicenter.
Refer All Communications to the Nearest
Ingersoll- - Rand Office or Distributor.
 Ingersoll- - Rand Company 2001
Printed in U.S.A.
INSTRUCTIONS FOR
MODELS 7803 AND 7803- -EU
HEAVY- -DUTY AIR DRILLS
IMPORTANT SAFETY INFORMATION ENCLOSED.
READ THIS MANUAL BEFORE OPERATING TOOL.
03533718
Keep hands, loose clothing, long hair and jewelry
away from rotating end of tool.
Keep body stance balanced and firm. Do not
overreach when operating this tool. Anticipate and
be alert for sudden changes in motion, reaction
torques, or forces during start- - up and operation.
Tool accessory may continue to rotate briefly after
throttle is released.
Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable positions may
be harmful to your hands and arms. Stop using
any tool if discomfort, tingling feeling or pain
occurs. Seek medical advice before resuming use.
Use accessories recommended by Ingersoll- - Rand.
This tool is not designed for working in explosive
atmospheres.
This tool is not insulated against electric shock.
Prevent exposure and breathing of harmful dust
and particles created by power tool use:
Some dust created by power sanding, sawing,
grinding, drilling and other construction
activities contains chemicals known to cause
cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
- - lead from lead based paints,
- - crystalline silica from bricks and cement
and other masonry products, and
- - arsenic and chromium from chemically
treated lumber.
Your risk from these exposures varies,
depending on how often you do this type of
work. To reduce your exposure to these
chemicals: work in a well ventilated area, and
work with approved safety equipment, such as
those dust masks that are specially designed to
filter out microscopic particles.
GB
Form P6713
Edition 9
September, 2001
Tabla de contenido
loading

Resumen de contenidos para Ingersoll Rand 7803

  • Página 13: Utilización De La Herramienta

    TALADROS NEUMÁTICOS DE SERVICIO PESADO MODELOS 7803 Y 7803- -EU NOTA Los taladros modelos 7803 y 7803- - EU están diseñados para taladrado, rectificación, escariado y perforación de agujeros. Ingersoll- - Rand no aceptará responsabilidad alguna por la modificación de las herramientas efectuada por el cliente para las aplicaciones que no hayan sido consultadas con Ingersoll- - Rand.
  • Página 14: Identificación De Símbolos De Aviso

    (A) vibraciones pulg. (mm) Presión Potencia 7803, 7803- - EU pistola 1/2 (13) 83,4 96,4 Probado en conformidad con PNEUROP PN8NTC1.2 a velocidad libre ♦ Probado en conformidad con ISO8662- - 1 80% de la velocidad libre nominal...
  • Página 15: Declaracion De Conformidad

    Swan Lane, Hindley Green, Wigan WN2 4EZ (domicilio) Declaramos que, bajo nuestra responsabilidad exclusiva, el producto: Taladros Neumáticos de Servicio Pesada Modelo 7803- EU a los que se refiere la presente declaración, cumplen con todo lo establecido en las directivas:...
  • Página 19 MAINTENANCE INSTRUCTIONS SECTION D’ENTRETIEN WARTUNG SEZIONE DI MANUTENZIONE INSTRUCCIONES DE MANTENIMIENTO ONDERHOUD (TPB753- -2)
  • Página 21 Si vous remplacez des pignons satellites de la broche, vous devez commander un kit de roulement de pignon satellite No. 7803- - K10. Le kit de roulement de pignon satellite contient 45 aiguilles de roulement et 10 rondelles de retenue, quantités suffisantes pour 5 pignons.

Este manual también es adecuado para:

7803-eu7802

Tabla de contenido