Operating The Tool; Recommended Hookup - Campbell Hausfeld SB524000 Manual Del Usuario

Operating Instructions
Important Safety Instructions
(Continued)
Do not drive a fastener
on top of other
fasteners. The fastener
could glance and cause death or a
serious puncture wound.
Do not operate or allow
anyone else to operate
the tool if any warnings
or warning labels are not legible.
Warnings or warning labels are located
on the tool magazine and body.
Do not drop or
throw the tool.
Dropping or throwing the tool can
result in damage that will make the tool
unusable or unsafe. If the tool has been
dropped or thrown, examine the tool
closely for bent, cracked or broken parts
and air leaks. STOP and repair before
using or serious injury could occur.
Always check that
the Work Contact
Element (WCE) is operating properly. A
fastener could accidentally be driven
if the WCE is not working properly.
Personal injury may occur (See
"Checking the Work Contact Element"
Section).
Avoid using the
tool when the
magazine is empty. Accelerated wear on
the tool may occur.
Clean and check all
air supply hoses
and fittings before connecting the
tool to an air supply. Replace any
damaged or worn hoses or fittings.
Tool performance or durability may be
reduced.
SeRvICe
a . Tool service must be performed only
by qualified repair personnel.
b . When servicing a tool, use only
identical replacement parts. Use
only authorized parts.
c . Use only the lubricants supplied
with the tool or specified by the
manufacturer.
www.chpower.com
the tool without first obtaining written
approval from Campbell Hausfeld. Do
not use the tool if any shields or guards
are removed or altered. Do not use the
tool as a hammer. Personal injury or
tool damage may occur.
tension from the pusher before
WARNING
!
attempting to clear jams because
fasteners can be ejected from the front
of the tool. Personal injury may occur.
aIR SOURCe
a . Never connect to an air source that
is capable of exceeding 200 psi.
Over pressurizing the tool is able
to result in bursting, abnormal
operation, breakage of the tool or
serious injury to persons . Use only
clean, dry, regulated compressed air
at the rated pressure or within the
rated pressure range as marked on
the tool . Always verify prior to using
the tool that the air source has been
adjusted to the rated air pressure or
within the rated air-pressure range .
b . Never use oxygen, carbon dioxide,
combustible gases or any bottled
gas as an air source for the tool.
Such gases are capable of explosion
and serious injury to persons .
Do not use any type of
reactive gases, including, but
not limited to, oxygen and
combustible gases, as a power source.
Use filtered, lubricated, regulated
compressed air only. Use of a reactive
gas instead of compressed air may
cause the tool to explode which will
cause death or serious personal injury.
Use only a pressure-regulated
compressed air source to limit
the air pressure supplied to
the tool. The regulated pressure must
not exceed 120 psi. If the regulator
fails, the pressure delivered to the
tool must not exceed 200 psi. The tool
could explode which will cause death or
serious personal injury.
Save TheSe INSTRUCTIONS
Do not make any
modifications to
Disconnect air
supply and release
O
120 psi
DO NOT DISCaRD
4

Operating The Tool

lUBRICaTION
This tool requires lubrication before
using the tool for the first time and
before each use . If an inline oiler is
used, manual lubrication through the
air inlet is not required on a daily basis .
damaged by excessive lubrication.
Proper lubrication is the owner's
responsibility. Failure to lubricate
the tool properly will dramatically
shorten the life of the tool and void the
warranty.
1 . Disconnect the air
supply from the tool
to add lubricant .
2 . Turn the tool so the
air inlet is facing up .
Place 4-5 drops of 30
W non-detergent oil
into air inlet . Do not
use detergent oils, oil
additives, or air tool oils . Air tool oils
contain solvents which will damage
the tool's internal components .
3 . After adding oil, run
tool briefly . Wipe off
any excess oil from
the cap exhaust .

ReCOMMeNDeD hOOkUP

CO
The illustration below shows the
2
recommended hookup for the tool .
1 . The air
compressor
must be able
to maintain a
minimum of 70
psi when the
tool is being used . An inadequate air
supply can cause a loss of power and
inconsistent driving .
2 . An oiler can be
used to provide oil
circulation through
the tool . A filter can
be used to remove
liquid and solid
impurities which can rust or "gum
up" internal parts of the tool .
The work surface
can become
70 psi
Min .
120 psi
Max .