Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Operating Instructions
General Safety
Information
(Continued)
G Always assume the tool contains
fasteners. Respect the tool as a
working implement; no horseplay.
Always keep others at a safe dis-
tance from the work area in case of
accidental discharge of fasteners.
Do not point the tool toward your-
self or anyone whether it contains
fasteners or not. Accidental trigger-
ing of the tool could result in death
or serious personal injury.
G Do not drive a fas-
tener on top of
other fasteners.
The fastener could
glance and cause
death or a serious
puncture wound.
G Do not operate
WARNING
or allow anyone
!
else to operate
the tool if any
warnings or
warning labels
are not legible.
Warnings or warning labels are locat-
ed on the tool magazine and body.
G Do not drop or throw the tool.
Dropping or throwing the tool can
result in damage that will make the
tool unusable or unsafe. If the tool
has been dropped or thrown, exam-
ine the tool closely for bent, cracked
or broken parts and air leaks. STOP
and repair before using or serious
injury could occur.
Caution indicates
CAUTION
!
a potentially haz-
ardous situation which, if not avoided,
MAY result in minor or moderate
injury.
G Do not make any modifications to the
tool without first obtaining written
approval from Campbell Hausfeld. Do
Recommended Hookup
not use the tool if any shields or
guards are removed or altered. Do
not use the tool as a hammer.
Personal injury or tool
damage may occur.
G Avoid long extended periods of
work with the tool. Stop using the
tool if you feel pain in hands or
arms.
G Always check that the Work Contact
Element (WCE) is operating proper-
ly. A fastener could accidentally be
driven if the WCE is not working
properly. Personal injury may occur
(See "Checking the Work Contact
Element" Section).
G Disconnect air supply and release
tension from the pusher before
attempting to clear jams because
fasteners can be ejected from the
front of the tool. Personal injury
may occur.
NOTICE
mation, that if not followed, MAY
cause damage to equipment.
G Avoid using the tool when the mag-
azine is empty. Accelerated wear on
the tool may occur.
G Clean and check all air supply hoses
and fittings before connecting the
tool to an air supply. Replace any
damaged or worn hoses or fittings.
Tool performance or durability may
be reduced.
Operating The
Stapler
LUBRICATION
This tool requires lubrication before
using the tool for the first time and
before each use. If an inline oiler is
Quick
Quick
Coupler
Plug
Air
Hose
used, manual lubrication through the
air inlet is not required on a daily basis.
aged by excessive lubrication. Proper
lubrication is the owner's responsibility.
Failure to lubricate the tool properly will
dramatically shorten the life of the tool
and void your warranty.
1. Disconnect the
2. Turn the tool so
Notice indicates
important infor-
3. After adding oil,
RECOMMENDED HOOKUP
The illustration below shows the
recommended hookup for the tool.
1. The air com-
Regulator
Quick Plug
(Optional)
Quick
Coupler
(Optional)
Lubricator
3
CHN10302
The work surface
NOTICE
can become dam-
air supply from
the tool to add
lubricant.
the air inlet is fac-
ing up. Place 4-5
OIL
OIL
drops of 30 W non-
detergent oil into
air inlet. Do not use
detergent oils, oil
additives, or air-
tool oils. Air tool oils contain sol-
vents which will damage the tool's
internal components.
run tool briefly.
Wipe off any
excess oil from the
cap exhaust.
pressor must be
able to main-
tain a mini-
mum of 60 psi
when the tool is being used. An
inadequate air supply can cause a
loss of power and inconsistent
driving.
Filter
www.chpower.com
60 psi
Min.
100 psi
Max.
Capítulos
Tabla de contenido
