Powerreclinexr + Troubleshooting - La-Z-Boy PowerRecline XR PLUS Instrucciones De Operación

PowerReclineXR
Operating Instructions
Press and hold the
button down to return
the back to the upright
position. Release the
button to stop the back
in any reclined position
or when fully raised.
Press and hold the
button down to close
the legrest and return
the chair body. Release
the button to stop the
legrest in any extended
position or when
fully closed.
Press and hold the
button down to raise
the back and close the
legrest and return the
chair body. Release
the button to stop the
chair in any position or
when the back is fully
raised and the legrest
is fully closed.
Press and hold the
button down to return
the headrest. Release
the button to stop the
headrest in any position
or when fully retracted.
Press and hold the button down
to decrease the lumbar intensity.
Release the button to stop the lumbar
in any position or when fully retracted.
WARNING
– To reduce the risk of serious injury:
• Do not use unit if power control is damaged or wet. Do not use unit if the hand wand has
been dropped in water or any liquid. Contact your La-Z-Boy
10
+
®
Press and hold the
button down to recline
the chair back. Release
the button to stop the
back in any reclined
position or when
fully reclined.
Press and hold the
button down to extend
the legrest and tilt the
chair body backward.
Release the button to
stop the legrest in any
extended position or
when fully raised.
Press and hold the
button down to recline
the back, extend
the legrest and tilt the
chair body backward.
Release the button to
stop the chair in any
position or when the
back is fully reclined
and the legrest is
fully raised.
Press and hold the
button down to rotate the
headrest forward. Release
the button to stop the
headrest in any position
or when fully forward.
Press and hold the button
down to increase the
lumbar intensity. Release
the button to stop the
lumbar in any position or
when fully extended.
® dealer for service.
PowerReclineXR
Troubleshooting
WARNING
– To reduce the risk of serious injury:
• Do not attempt to disassemble or service the pump or motor; no serviceable parts are
inside. Contact your La-Z-Boy dealer for service.
®
• Check the condition of the power transformers, electrical cords, plugs, and connectors
monthly. Keep the power transformers and electrical cords away from heat sources.
Never operate the unit with a damaged power transformer, electrical cord, plug, or
connector. Contact your La-Z-Boy ® dealer for service.
+
• The PowerReclineXR
®
units are intended for a single occupant not exceeding 300 pounds
per seat. Do not operate an individual seat with more than one occupant in or on any part
of the individual seat.
If the legrest stops moving while closing, it may have encountered an obstruction. The legrest
uses spring tension to close, and will close quickly when the obstruction is removed. Lift and
hold the legrest up and remove the obstruction. Release the legrest slowly to prevent it from
slamming shut.
+
If the PowerReclineXR ® does not work, check the following:
1. Make sure the 120 volt power cord is plugged into an electrical outlet.
2. Check the power transformer to make sure the green LED power indicator light is on.
3. Make sure the electrical outlet is working. For example, make sure there are no blown
fuses or tripped circuit breakers.
4. Make sure all the connectors are secure; refer to the Assembly Instructions.
5. Make sure the electrical cords are not crimped or pinched. Make sure the electric cord
or plug is not damaged.
6. Make sure the operating capacity has not been exceeded and there is only one occupant
in the individual seat or unit; refer to the Operating Instructions.
+
If the PowerReclineXR ® still does not operate properly, contact your dealer for instructions on
returning the unit for examination and repair. Except for the replacement of the power transformer,
never attempt to make any repairs or adjustments yourself.
Power Transformer Replacement
If the power transformer must be replaced:
1. Unplug the power transformer from the electrical outlet.
2. Disconnect the 120 volt power cord from the power transformer, and disconnect the power
transformer from the power supply connector; refer to the Assembly Instructions.
3. Connect the new power transformer to the power supply connector, and close the locking cover.
Connect the 120 volt power cord to the new power transformer; refer to the Assembly Instructions.
4. Proceed to the Battery Backup Assembly Instructions.
+
®
11