Tabla De Contenido; Important Safety Information; Safety - WAGNER HVLP Manual Del Usuario

Important Safety Information

Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
To reduce the risks of fire or explosion, electrical
shock and the injury to persons, read and understand
all instructions included in this manual. Be familiar
with the controls and proper usage of the equipment.
haZaRD: EXPLOSION haZaRD DuE TO
INCOMPaTIBLE MaTERIaLS
Will cause property damage or severe injury.
PREvENTION:
• Do not use materials containing bleach or chlorine.
• Do not use halogenated hydrocarbon solvents such as bleach,
mildewcide, methylene chloride and 1,1,1 - trichloroethane. They are
not compatible with aluminum.
• Contact your coating supplier about the compatibility of material with
aluminum.
haZaRD: GENERaL
Can cause severe injury or property damage.
PREvENTION:
• Read all instructions and safety precautions before operating any
equipment.
• Follow all appropriate local, state, and national codes governing
ventilation, fire prevention, and operation.
• The United States Government Safety Standards have been adopted
under the Occupational Safety and Health Act (OSHA). These
standards, particularly Part 1910 of the General Standards and Part
1926 of the Construction Standard should be consulted.
• Use only manufacturer authorized parts. User assumes all risks
and liabilities when using parts that do not meet the minimum
specifications and safety devices of the manufacturer.
• Before each use, check all hoses for cuts, leaks, abrasion or bulging
of cover. Check for damage or movement of couplings. Immediately
replace the hose if any of these conditions exist. Never repair a hose.
Replace it with an identical replacement hose.
• Do not spray outdoors on windy days.
• Wear clothing to keep paint off skin and hair.
• Never aim the spray gun at any part of the body.
haZaRD: haZaRDOuS vaPORS
Paints, solvents, insecticides, and other
materials can be harmful if inhaled or come
in contact with the body. Vapors can cause
severe nausea, fainting, or poisoning.
PREvENTION:
• Use a respirator or mask if vapors can be inhaled. Read all instructions
supplied with the mask to be sure it will provide the necessary
protection.
• Wear protective eyewear.
• Wear protective clothing as required by coating manufacturer.
English
·
Read all safety information before operating
the equipment. SavE ThESE INSTRuCTIONS.
PREvENTION:
Table of Contents
Safety ................................................................................................ 2
Introduction ..................................................................................... 3
using an hvLP Spray Gun ............................................................3-4
Cleaning the Spray Gun .................................................................. 5
Maintenance .................................................................................5-7
Converting to a Single Pin Trigger ................................................. 7
Choosing a Projector Set ................................................................. 7
Optional accessories ....................................................................... 8
Material reduction/projector set chart .......................................... 9
Troubleshooting .............................................................................. 9
Regulator Cup Gun Parts List ..................................................26-27
Français .......................................................................................... 10
Español ........................................................................................... 18
Warranty ........................................................................................ 28
2
haZaRD: EXPLOSION OR FIRE
Solvent and paint fumes can explode or
ignite. Property damage and/or severe injury
can occur.
• Provide extensive exhaust and fresh air introduction to keep the air
within the spray area free from accumulation of flammable vapors.
• Avoid all ignition sources such as static electric sparks, open flames,
pilot lights, and hot objects. Connecting or disconnecting power
cords or working light switches can make sparks.
• Do not smoke in spray area.
• Fire extinguisher must be present and in good working order.
• The power cord must be connected to a grounded circuit.
• Follow the material and solvent manufacturer's safety precautions and
warnings.
• Use extreme caution when using materials with a flashpoint below
70° F (21° C). Flashpoint is the temperature that a fluid can produce
enough vapors to ignite.
• Plastic can cause static sparks. Never hang plastic to enclose a spray
area. Do not use plastic drop cloths when spraying flammable
materials.
Preparing to Spray........................................................................................3
Selecting a Spray Pattern ...........................................................................3
Spray Pattern Size .........................................................................................4
Adjusting the Material Flow .....................................................................4
Spraying ...........................................................................................................4
Adjusting the Suction Tube ......................................................................4
Adjusting the Packing Nut ........................................................................5
Replacing the Needle Packing and Air Valve Seals ..........................5
Replacing the Check Valve, Valve Seal, and Air Tubes ....................6
Replacing the Cup Gasket .........................................................................7
Changing a Projector Set ...........................................................................7
© Wagner Spray Tech. All rights reserved.