Tabla de contenido
Idiomas disponibles
Idiomas disponibles
NOTICE
j Improper treatment of pressure washer can damage it and
W_orten
_
....
_tsq_fe,
DONOT insert anyobjectsthroughcoolingslots.
°
Usea vacuumcleanerto pick up loose dirt and debris.
Check and Cmean[n_et Screen
Examine garden hose inlet screen. Clean if it is clogged or
repiace if it is torn.
Check High Pressure Hese
High pressure hoses can develop leaks from wear, kinking,
or abuse, inspect hose before each use. Checkfor cuts,
leaks, abrasions, bulging of cover, or damage or movement
of coupiings. If any of these conditions exist, replace hose
immediately.
1
wA G
pressure stream
)ossibte
1
Dutation.
NEVER repairhigh pressure hose.Replace it.
Replacement hoseratingMUSTexceedrnaxhnurn pressure
ratingof unit.
Check Detergent $iphening Tube
Examine the filter on the detergent tube and clean if clogged.
The tube should fit tightly on the barbed fitting. Examinethe
tube for ieaks or tears. Replacethe filter or tube if either is
damaged.
Check Gurt and Nozzle Extensien
Examine the hose connection to the spray gun and make
sure it is secure. Test the trigger by pressing the red button
and making sure the trigger "springs back" into place when
you releaseit. You should not be abie to press the trigger
without pressing the red button. Repiace spray gun
immediately if it faiis any of these tests.
Nezzle Maintenance
A pulsing sensation feit while squeezingthe spray gun trigger
may be caused by excessive pump pressure. The principai
cause of excessive pump pressure is a nozztectogged or
restricted with foreign materiais, such as dirt, etc. To correct
the probiem, immediateiy clean the nozzle following these
instructions:
,
2.
Shut off engine and turn off water suppiy.
ALWAYSpoint spray gun in a safe direction, press red
button and squeeze spray gun trigger to releaseretained
high water pressure.
WARNING
The high pressure stream of water that this
equipment produces can cut through skin and its
_
nderiying tissues, ieading to serious injury and
)ossibie amputation.
Spray gun traps Ngh water pressure, even when
engine is stopped and water is disconnected,
which can cause injury.
• Keephigh pressurehoseconnected to purnpand spraygun
whilesystemis pressurized.
o ALWAYS pointspraygemin safedirection,pressred button
and squeeze spraygun trigger,to releasehigh pressure, e very
time youstop engine.
3.
Remove nozzlefrom end of nozzle extension.
4.
Use a smali paper clip to free any foreign material
clogging or restricting nozzle (A).
,
6.
Remove nozzteextension from spray gun.
Using a garden hose, remove additionai debris by back
flushing water through nozzteextension. Back flush
between 30 to 60 seconds.
jJ
.
8.
9.
10.
11.
_j
........
Reinstaii nozzle into nozzle extension.
Reconnect nozzle extension to spray gun.
Make sure garden hose is connected to water inlet.
Checkthat high pressure hose is connected to spray gun
and pump. Turn on water.
Start engine foiiowing instructions How to Start Your
Pressure Washe,<
Test pressure washer by operating with each quick
connect nozzle.
e-Ring Maintenance
Purchase an O-Ring Repair Kit at your Iocai Sears or by
cailing I-See-4-MY-NOME (469-4663) or ontine at
www.sears.com, it is not included with the pressure washer.
This kit includes repiacement o-rings, rubber washer and
water inlet fiiter. Refer to tile instruction sheet provided in the
kit to service your unit's o-rings=
WARNING
The high pressure stream of water that this
_
quipment produces can cut through skin and its
underlying tissues, ieading to serious injury and
)ossibte amputation.
° NEVER repairleakingconnections with sealant o f anykind.
Replace o-ring or seal.
18
Tabla de contenido
