Ingersoll Rand HA–EU Serie Instrucciones
Ingersoll Rand HA–EU Serie Instrucciones

Ingersoll Rand HA–EU Serie Instrucciones

Lijadoras angulares neumáticas
Ocultar thumbs Ver también para HA–EU Serie:
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 17

Enlaces rápidos

INSTRUCTIONS FOR SERIES HA–EU AND HXA–EU
Series HA–EU and HXA–EU Angle Sanders are designed for smoothing, trimming or
removing metal in close–quarter areas in foundries, shipyards, steel mills and in
construction applications.
Ingersoll–Rand is not responsible for customer modification of tools for applications on
which Ingersoll–Rand was not consulted.
IMPORTANT SAFETY INFORMATION ENCLOSED.
READ THIS MANUAL BEFORE OPERATING TOOL.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THE INFORMATION
IN THIS MANUAL INTO THE HANDS OF THE OPERATOR.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
PLACING TOOL IN SERVICE
Always operate, inspect and maintain this tool in
accordance with all regulations (local, state, federal
and country), that may apply to hand held/hand
operated pneumatic tools.
For safety, top performance, and maximum
durability of parts, operate this tool at 90 psig
(6.2 bar/620 kPa) maximum air pressure at the inlet
with 3/8" (10 mm) inside diameter air supply hose.
Always turn off the air supply and disconnect the
air supply hose before installing, removing or
adjusting any accessory on this tool, or before
performing any maintenance on this tool.
Do not use damaged, frayed or deteriorated air
hoses and fittings.
Be sure all hoses and fittings are the correct size
and are tightly secured. See Dwg. TPD905–1 for a
typical piping arrangement.
Always use clean, dry air at 90 (6.2 bar/620 kPa)
psig maximum air pressure. Dust, corrosive fumes
and/or excessive moisture can ruin the motor of an
air tool.
Do not lubricate tools with flammable or volatile
liquids such as kerosene, diesel or jet fuel.
Do not remove any labels. Replace any damaged
label.
The use of other than genuine Ingersoll–Rand replacement parts may result in safety hazards, decreased tool
performance, and increased maintenance, and may invalidate all warranties.
Repairs should be made only by authorized trained personnel. Consult your nearest Ingersoll–Rand Authorized
Servicenter.
Refer All Communications to the Nearest
Ingersoll–Rand Office or Distributor.
Ingersoll–Rand Company 1998
Printed in U.S.A.
AIR ANGLE SANDERS
USING THE TOOL
Always wear eye protection when operating or
performing maintenance on this tool.
Always wear hearing protection when operating
this tool.
Keep hands, loose clothing and long hair away from
rotating end of tool.
Anticipate and be alert for sudden changes in
motion during start up and operation of any power
tool.
Keep body stance balanced and firm. Do not
overreach when operating this tool. High reaction
torques can occur at or below the recommended air
pressure.
Tool accessories may continue to rotate briefly after
throttle is released.
Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable positions may
be harmful to your hands and arms. Stop using any
tool if discomfort, tingling feeling or pain occurs.
Seek medical advice before resuming use.
Use accessories recommended by Ingersoll–Rand.
This tool is not designed for working in explosive
atmospheres.
This tool is not insulated against electric shock.
04575833
Form P7356–EU
Edition 3
December, 1998
GB
Tabla de contenido
loading

Resumen de contenidos para Ingersoll Rand HA–EU Serie

  • Página 17: Instrucciones Para Lijadoras Angulares Neumaticas De Las Series Ha-Eu Y Hxa-Eu

    04575833 Impreso P7356–EU Edición 3 Diciembre, 1998 INSTRUCCIONES PARA LIJADORAS ANGULARES NEUMATICAS DE LAS SERIES HA–EU Y HXA–EU NOTA Las Lijadoras y Angulares Neumáticas Serie HA–EU, HXA–EU están diseñadas para pulido, recorte o eliminación de metal en fundiciones, astilleros, fábricas de acero y en la industria de construcción.
  • Página 18: Etiquetas De Aviso

    ETIQUETAS DE AVISO AVISO EL HACER CASO OMISO DE LOS AVISOS SIGUIENTES PODRIA OCASIONAR LESIONES. ADVERTENCIA ADVERTENCIA ADVERTENCIA Cortar siempre el suministro Usar siempre protección ocular Usar siempre protección de aire y desconectar la man- al manejar o realizar opera- para los oìdos al manejar guera de suministro de aire ciones de mantenimiento en...
  • Página 19: Especificaciones

    AVISOS ESPECIFICOS DE LIJADORA ESPECIFICACIONES Lijadoras angulares con pinza de 1/4” HNivel de Sonido Modelo Velocidad Nivel de Constante dB (A) Vibraciones Presión Potencia HA40RSG4ML–EU 4 000 85,5 98,5 HA60RSG4ML–EU 6 000 86,1 99,1 Lijadoras angulares con husillo roscado 5/8”– 11 HNivel de Sonido Modelo Velocidad...
  • Página 20: Declaracion De Conformidad

    DECLARACION DE CONFORMIDAD Ingersoll–Rand, Co. os abajo firmantes (nombre del proveedor) Swan Lane, Hindley Green, Wigan WN2 4EZ (domicilio) Declaramos que, bajo nuestra responsabilidad exclusiva, el producto: Lijadoras Amoladoras Angulares Modelo HA–EU, HXA–EU a los que se refiere la presente declaración, cumplen con todo lo establecido en las directivas: 98/37/CE ISO8662 PNEUROP PN8NTC1.2...
  • Página 26 Service Centers Centres d’entretien Niederlassungen Centri di Assistenza Centros de Servicio Service Centra Ingersoll–Rand Company Ingersoll–Rand Nederland Produktieweg 10 510 Hester Drive 2382 PB Zoeterwoude White House Nederland TN 37188 Tel: (31) 71 452200 Fax: (31) 71 5218671 Tel: (615) 672 0321 Fax: (615) 672 0601 Ingersoll–Rand Company SA PO Box 3720...

Tabla de contenido