Ingersoll Rand 285A Instrucciones página 19

1 Trigger Handle Assembly . . . . . .
2 Plunger Bushing . . . . . . . . . . . . 291–303
3 Reverse Valve Bushing . . . . . . 285–330A
4 Trigger . . . . . . . . . . . . . . . . . . . 285–93A
5 Spring Pin . . . . . . . . . . . . . . . . 281–437
6 Stop Pin . . . . . . . . . . . . . . . . . . 281–439
7 Slot Cover . . . . . . . . . . . . . . . . 281–438
8 Throttle Valve . . . . . . . . . . . . . . .
9 Throttle Valve Plunger . . . . . . . . .
10 Throttle Valve Spring . . . . . . . . . .
11 Inlet Bushing . . . . . . . . . . . . . . . .
15 O–ring . . . . . . . . . . . . . . . . . . . 291–566
17 Reverse Valve Assembly . . . . . . .
18
Reverse Valve Seal . . . . . . . . . 291–338
19 Stop Pin . . . . . . . . . . . . . . . . . . 291–332
19A Ball . . . . . . . . . . . . . . . . . . . . . . 291–333
20 Spring . . . . . . . . . . . . . . . . . . . . . .
21 Spring Pin . . . . . . . . . . . . . . . . . .
22 Handle Gasket . . . . . . . . . . . . . . .
23 Handle Cap Screw (4) . . . . . . . . .
24 Handle Cap Screw
Lockwasher (4) . . . . . . . . . . . . . .
25 Motor Housing . . . . . . . . . . . . . . .
26 Rear Rotor Bearing . . . . . . . . . . .
27 Rear End Plate Assembly . . . . . .
28 Pin . . . . . . . . . . . . . . . . . . . . . . 291–10
29 Rotor . . . . . . . . . . . . . . . . . . . . . .
30 Vane Packet (set of 6 vanes) . . . .
31 Cylinder Assembly . . . . . . . . . . .
32 Cylinder Dowel (2) . . . . . . . . . 291–98
33 Front End Plate . . . . . . . . . . . . . .
MAINTENANCE INSTRUCTIONS
SECTION D'ENTRETIEN
WARTUNG
SEZIONE DI MANUTENZIONE
INSTRUCCIONES DE MANTENIMIENTO
ONDERHOUD
285–A92A
285–50
285–302
291–51
291–A565
285–A329
291–334
281–120
285–283
281–638
291–104
285–40
291–24
291–A12
285–53
291–42–6
285–A3
291–11
PART NUMBER FOR ORDERING
REFERENCE POUR COMMANDE DE LA PIECE
BESTELLNUMMER
NUMERO DEL PEZZO PER L'ORDINAZIONE
SIMBOLO DE LA PIEZA PARA PEDIDOS
BESTELNUMMERS
34 Front Rotor Bearing . . . . . . . . . . . . . . . . . . .
35 Hammer Frame . . . . . . . . . . . . . . . . . . . . . .
36 Hammer Cam . . . . . . . . . . . . . . . . . . . . . . . .
37 Hammer . . . . . . . . . . . . . . . . . . . . . . . . . . . .
38 Side Plate . . . . . . . . . . . . . . . . . . . . . . . . . . .
1" Square Drive Anvil Assembly
39 Standard Length . . . . . . . . . . . . . .
39A 6" Extended Length . . . . . . . . . . . .
40 Spline Drive Anvil Assembly
(6" Extended length) . . . . . . . . . . . . . . . . . .
41 Retainer Ring . . . . . . . . . . . . . . . . . . . . .
42 Retainer O–ring . . . . . . . . . . . . . . . . . . .
43 Hammer Case Assembly . . . . . . . . . . . . . . .
44
Hammer Case Bushing . . . . . . . . . . . . .
45 Oil Seal . . . . . . . . . . . . . . . . . . . . . . . . .
46 Warning Label . . . . . . . . . . . . . . . . . . . .
47 Hammer Case Gasket . . . . . . . . . . . . . . . . .
48 Hammer Case Cap Screw (4) . . . . . . . . . . .
49 Hammer Case Cap Screw
Lockwasher (4) . . . . . . . . . . . . . . . . . . . . . .
50 Dead Handle (for 285A) . . . . . . . . . . . . . . .
51 Dead Handle (for 285A–6 and 285A–S–6) .
52 Dead Handle Cap Screw (4) . . . . . . . . . . . .
53 Dead Handle Cap Screw
Lockwasher (4) . . . . . . . . . . . . . . . . . . . . . .
54 Nameplate Screw (2) . . . . . . . . . . . . . . . . . .
55 Nameplate
for 285A . . . . . . . . . . . . . . . . . . . . .
for 285A–S–6 . . . . . . . . . . . . . . . .
for 285A–6 . . . . . . . . . . . . . . . . . . .
19
(TPA1716)
58–96
285–703
285–721
285–724
285–706
285–A726
285–A726–6
285–A514–6
291–425
291–426
285–A727
291–641
291–642
WARNING–27–99
285–36
291–105
291–104
291–48
281–48–6
291–49
291–504
222–302
285A–301
285A–S–6–301
285A–6–301