Remote Control - Cardin YPR851BCC Manual Del Usuario

CONTINUED FROM PAGE 9
PRESSING THE "PROG" BUTTON MOVES YOU TO STAGE "C".
SETTING THE PAUSE TIME.
THE START OF THE STAGE IS
INDICATED BY THE LETTER "t"
APPEARING FOR 2 SECONDS AFTER
WHICH THE DISPLAY SWITCHES OFF
THE OPENING TIME STARTS, THE
CURRENT SENSOR WILL BE UPDATED
AND THE BOOM WILL BE STOPPED
AUTOMATICALLY WHEN IT ARRIVES AT
THE COMPLETELY OPEN POSITION.
AT THIS POINT THE PAUSE TIME WILL START.
Automatic
reclosing
enabled
THE PAUSE TIME ENDS AND
RECLOSING STARTS, THE
CURRENT SENSOR CONTINUES
CALIBRATING UNTIL THE BOOM IS
COMPLETELY CLOSED.
THE OPERATION WAS
NOT SUCCESSFUL YOU
WILL HAVE TO REPEAT
PROGRAMMING
PROGRAMMING THE PAUSE CYCLE TIMES
The only work time that requires programming is the pause time; the work
cycle time in fact is automatically managed by the programmer and is regulated
according to the impulses given by the travel limits in the following way:
• When the boom enters the area between the travel limits a 20 second
(maximum) manoeuvre time should be set.
• When the boom enters the area between the travel limits and the completely
closed/open position a 6 second (maximum) manoeuvre time should be set.
This means that you have to adjust the travel limits (for safety) so that the
slow movement time period doesn't exceed 5 seconds. If this is not done
the boom will stop before it reaches the completely closed/open position.
Attention! Pressing the "SEL" button during work time program-
ming will exit the programming mode without memorising the
modified work cycle times.

REMOTE CONTROL

The motor can be remotely activated using a transmitter: only the sequential
function is available "open-stop-close-stop" and this may be activated from
any of the available channels.
For this reason for each transmitter enabled you need only use one of the
available channels.
S449 SERIES RADIOCONTROLS
Memory module
This is extractable, furnished with a non volatile EEPROM type memory and
contains the transmitter codes and allows you to memorise up to 300 codes
(300 channel buttons). The programmed codes are maintained in this module
even in the absence of power.
Attention! Before memorising the transmitters for the first time
remember to cancel the entire memory content.
If the electronic card has to be replaced due to failure, the module
can be extracted from it and inserted into the new card. Make sure
that the module is orientated in the direction shown in detail A.
on page 28.
PRESS
SEL
THE PROGRAMMER SAVES
ALL DATA AND QUITS
PRESS
PROGRAMMING WITHOUT
PROG
MODIFYING THE TIMES IN
MEMORY.
...2... sec.
Automatic
reclosing
excluded
PRESS PROG
WHEN THE BOOM ARRIVES AT THE
COMPLETELY CLOSED POSITION
THE PROGRAMMER SAVES THE
PARAMETERS AND QUITS
PROGRAMMING.
Signal LED "L2" (pag. 28):
Flashing quickly: cancels a single code
Flashing slowly: memorises a single code
Permanently lit: memory full.
TRANSMITTER CODE MANAGEMENT
A. Memorising a channel (using the associated transmitter)
B. Cancelling a channel (using the associated transmitter)
C. Cancelling all codes in memory
D. Memorising ulterior channels via radio (without having to open the box
in which the programmer is housed)
A) MEMORISING A CHANNEL (pag. 28):
1. Press and hold down button "P3" MEMO: The LED "L2" will flash
slowly.
2. At the same time activate the transmitter which is to be memorised.
3. Hold down button "P3" MEMO until LED "L2" starts to flash again.
4. Release the button: The LED will continue to flash.
5. Activate the transmitter again (same transmitter, same channel; if the chan-
nel is different or it is a different transmitter the memorisation attempt will
abort without success)
6. End of memorisation: The LED "L2" will remain lit for 2 seconds, indicating
that the transmitter has been correctly memorised.
Note: It is not possible to memorise a code which is already in memory:
if you attempt this, the LED will switch off when you activate the transmitter
(point "2").
Only after releasing the button "P3" MEMO will you be able to continue the
memorising procedure. If after activating the transmitter for the first time you
wait for more than fifteen seconds without activating the transmitter a second
time the memorisation attempt will abort without success.
B) CANCELLING A CHANNEL (pag. 28):
1. Press and hold down the button "P4" DELETE: The LED "L2" will flash
quickly.
2. Activate the transmitter channel which is to be cancelled.
3. The LED "L2" will remain lit for 2 seconds, indicating that the transmitter
has been cancelled.
Note: if the user that you wish to cancel is not in memory, the LED will stop
flashing; Only after releasing the button "P4" will you be able to continue the
cancellation procedure.
For both the memorisation and cancellation procedures, if the button is released
before activating the transmitter the procedure will abort.
C - CANCELLING ALL USER CODES FROM MEMORY (pag. 28):
1. Keep both buttons pressed down ("P3 + P4") for more than four sec-
onds
2. LED "L2" will remain lit during the entire cancellation time (about 8 sec-
onds).
3. LED "L2" switches off when the cancellation procedure has terminated.
Note: When the memory is almost full the time required to search for a user
code could take up to 1 second from when the command was received. If LED
"L2" remains alight memory is completely full. To memorise a new transmitter
you will first have to cancel a code from memory.
D- MEMORISING ULTERIOR CHANNELS VIA RADIO
• Memorisation can be activated by radio (without opening the receiver
container) if jumper "J2" has been inserted (pag. 28).
1) Make sure that the jumper "J2" has been
inserted (pag. 28).
2) Using a transmitter, in which at least one
channel button "A,B,C,D" has already been
memorised in the receiver, press the button
in the transmitter as shown in the figure.
Note: all the receivers within range when
the channel button is pressed (and which
have at least one of the transmitter channel
buttons memorised) will activate their signal
buzzer "B" (pag. 28).
3) Press one of the channel buttons on the same transmitter. The receiv-
ers which do not contain that channel code will sound a five-second
long "beep" and will then deactivate. The receivers which contain the
channel code will sound a one-second long "beep" and will enter the
programming "via radio" mode.
0
All rights reserved. Unauthorised copying or use of the information contained in this document is pu
Description : MEMORIZZAZIONE CODICE TX-RX
Drawing number : DM0531
Product Code : RCQ449100
Date : 13-04-2001
Draft : P.J.Heath
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/40