Using The Menu; Setting The Language; Memorizing Channels - Dynex DX-R32TV Guía Del Usario

Setting up the television

Using the menu

To access the menu using the TV buttons:
• Press both of the CH and CH
menu screen appears.
To access the menu using the remote control:
• Press MENU/ENTER. The menu screen appears.
To select a setting using the TV buttons:
• Use the CH and CH
buttons.
To select a setting using the remote control:
• Use the CH + and CH - buttons and the VOL + and VOL - buttons.

Setting the language

You can choose from three different languages (English, French, and
Spanish) for the on-screen displays.
To select a menu language:
1 Press MENU/ENTER. The menu screen appears.
Note:
If no buttons are pressed for more than 60 seconds, the menu screen returns
to normal television operation automatically.
2 Press the VOL + and VOL - buttons to select SETUP menu.
3 Press the CH + and CH - buttons to select LANGUAGE, then press
the VOL + button.
4 Press the VOL + and VOL - buttons to select the desired language:
• English (ENGLISH),
• French (FRANÇAIS), or
• Spanish (ESPAÑOL).
5 Press EXIT to return to the normal screen.

Memorizing channels

This television is equipped with a channel memory feature which allows
channels to skip up or down to the next channel set into memory,
skipping over unwanted channels. Before selecting channels, they must
be programmed into the television' s memory.
To use this television with an antenna, set the TV/CABLE menu option to
the TV mode. When shipped from the factory, this menu option is in the
CABLE mode.
Selecting TV or cable
To select TV or cable input:
1 Press MENU/ENTER. The menu screen appears.
2 Press the VOL + and VOL - buttons to select the SETUP menu.
3 Press the CH + and CH - buttons to select TV/CABLE.
4 Press the VOL + and VOL - buttons to select TV or CABLE.
• TV—VHF/UHF channels
• CABLE—Cable television channels
5 Press EXIT to return to the normal screen.
Note:
It may take a few seconds for a digital channel picture to appear on screen
after being selected.
buttons at the same time. The
buttons and the VOL and VOL
Cable chart
The following chart is typical of many cable system channel allocations.
The number on the top is the number on the television. The number or
letter on the bottom is the corresponding cable channel.
Automatic memory tuning
Memorizing channels is best accomplished during evening "primetime"
hours, as more channels are broadcasting digital signals. Memorizing
channels can only be accomplished while a station is broadcasting a
digital signal to set the channel into memory.
If you are not sure of the digital channels available in your area, visit
www.antennaweb.org to find a list based on your address or zip code.
To automatically memorize channels:
1 Press MENU/ENTER. The menu screen appears.
2 Press the VOL + and VOL - buttons to select the SETUP menu,
then press the CH + and CH - buttons to select AUTO CH
MEMORY.
3 Press the VOL + button. The television begins memorizing all of
the channels available in your area.
After completing analog tuning, digital tuning starts
automatically. Depending on the reception condition, it may take
from 15 to 30 minutes to complete memorizing digital cable
channels. Depending on the condition of the reception, the BAR
display may not advance for several minutes.
Note:
Some new channels may be added. You should complete the AUTO CH
MEMORY procedure periodically.
Adding and deleting channels
To add or delete analog channels:
1 Press TUNER to select the Analog mode.
2 Press MENU/ENTER. The menu screen appears.
3 Press the VOL + and VOL - buttons to select the OPTION menu,
then press the CH + and CH - buttons to select ADD/DELETE.
4 Press the VOL + button. The ADD/DELETE menu appears.
5 Select the desired channel to be memorized or deleted using the
CH + and CH - buttons.
6 Press the VOL + and VOL - buttons to select ADD or DELETE.
7 Repeat steps 5-6 for other channels you want to add or delete.
8 Press EXIT to return to the normal screen.
To add or delete digital channels:
1 Press TUNER to select the Digital mode.
2 Press MENU/ENTER. The menu screen appears.
3 Press the VOL + and VOL - buttons to select the OPTION menu,
then press the CH + and CH - buttons to select DIGITAL SETUP.
4 Press the VOL + button. The DIGITAL SETUP menu appears.
5 Press the CH + and CH - buttons to select ADD/DELETE, then
press the VOL + button. The ADD/DELETE (DTV) menu appears.
6 Press the CH + and CH - buttons to select ADD/DELETE, then
press the VOL + button.
7 Select the desired channel to be memorized or deleted using the
CH + and CH - buttons.
8 Press the VOL + and VOL - buttons to select ADD or DELETE.
9