Using The Tv; Viewing Information - Dynex DX-R32TV Guía Del Usario

10
9 Repeat steps 6-8 for other channels you want to add or delete,
then press MENU/ENTER.
10 Press MENU/ENTER repeatedly to return to the normal screen.
To add a digital channel you are watching:
1 Press TUNER to select the Digital mode. Use the number buttons
to directly select the digital channel you want to add.
2 Press MENU/ENTER. The menu screen appears.
3 Press the VOL + and VOL - buttons to select the OPTION menu,
then press the CH + and CH - buttons to select DIGITAL SETUP.
4 Press the VOL - button. The DIGITAL SETUP menu appears.
5 Press the CH + and CH - buttons to select ADD/DELETE, then
press the VOL - button. The ADD/DELETE (DTV) menu appears.
6 Press the CH + and CH - buttons to select ADDING CHANNEL,
then the VOL + button.
7 Press MENU/ENTER repeatedly to return to the normal screen.
8 Repeat steps 1-7 for other channels you want to add directly.

Using the TV

Notes:
If you select a channel with no broadcast signal, the sound is automatically
muted.
If a station you are viewing stops broadcasting, the television automatically
shuts itself off after 15 minutes.
To use the television:
1 Press POWER to turn on the television.
2 Adjust the volume level by pressing the VOL
buttons on the TV or the VOL + and VOL - buttons on the remote
control. The volume level is indicated on the screen by green bars.
As the volume level increases, so do the number of bars. If the
volume decreases, the number of green bars also decreases.
3 Set the TV/CABLE menu option to the appropriate position (see
"Selecting TV or cable" on page 9).
4 Press the direct channel selection buttons to select the channel.
Selecting analog channels
When the TV/CABLE menu option is the TV position, all channels can be
instantly selected by using two buttons.
For example, to select channel 2, press 0, then 2. If you press only 2,
channel selection will be delayed for a few seconds. For channels 10 and
above, press the two digits in order.
When the TV/CABLE menu option is the CABLE position, channels can be
selected as follows:
Channels Press
1-9 Press 0 twice, then 1-9 as needed.
Example: to select channel 2, press 0 0 2.
10-12 Press 0, then the remaining 2 digits.
Example, to select channel 12, press 0 1
2.
13-99 Press the 2 digits in order.
Example, to select channel 36, press 3 6.
100-125 Press the 3 digits in order. Example, to
select channel 120, press 1 2 0.
Selecting digital channels
To select digital channels, press the channel number in order.
When – is contained in the channel number, press the first three digits,
then press –/DISPLAY, followed by the remaining three digits.
Example, to select channel 015-001, press 0 1 5 – 0 0 1.
Note the following:
• If a channel is selected with only audio content, "AUDIO ONLY" will
be displayed on the screen.
• If a channel is selected with a weak digital signal, "DIGITAL
CHANNEL SIGNAL STRENGTH IS LOW" will be displayed on the
screen.
• If the digital channel has the same analog channel, you may be
able to watch the same channel on analog.
• If a channel is selected to which you have not subscribed, "DIGITAL
CHANNEL IS ENCRIPTED" will be displayed on the screen.
TV
VHF
2-13
UHF
14-69
Seeking channels
To seek the next channel:
• Press and release the CH + and CH - buttons. The channel
automatically stops at the next channel set into memory.
For proper operation, before seeking channels, channels should be set
into the memory. See "Memorizing channels" on page 9.

Viewing information

Note:
and VOL
The screen automatically returns to normal TV operation after 10 seconds.
To view program information:
1 Press -/DISPLAY to display the current information on the screen.
When the television receives a digital signal, the digital
information appears:
• Broadcast program name
• Station name
• Remaining time
• Audio language
• Program name
• V-Chip rating
• V-Chip mark
When the television receives an analog signal, –/DISPLAY shows
only analog information.
2 Press –/DISPLAY again. The analog information appears.
• Clock
• Channel number or video mode selected
• Channel label (if preset)
• Stereo or SAP (second audio program) audio status
• Picture size
3 Press –/DISPLAY again to clear the call display.
Viewing the previous channel
The RECALL button allows you to go back to the last channel viewed.
Press RECALL again to return to the last channel you were watching.
Muting the volume
To mute the volume:
1 Press MUTE to turn off the sound. The television' s sound is
silenced and MUTE appears on the screen.
2 Switch the sound back on by pressing MUTE again or by pressing
the VOL + or VOL – button.
Using sleep
To set the sleep function:
To set the television to turn off after a preset amount of time, press
SLEEP on the remote control. The clock counts up ten (10) minutes for
each press of the SLEEP button (0, 10, 20...100, 110, 120).
Using the TV
Cable
VHF
2-13
STD/HRC/IRC
14-36 (A) (W)
37-59 (AA) (WW)
60-85 (AAA) (ZZZ)
86-94 (86) (94)
95-99 (A-5) (A-1)
100-125 (100) (125)
01 (5A)