Makita DCL281F Manual De Instrucciones página 13

When using attachment without lock
function
CAUTION:
To connect attachment without
lock function, twist and insert it in direction of
the arrow to secure the connection during use.
To disconnect the attachment, twist and extract
it also in direction of the arrow. If the attachment
is twisted in the opposite direction, the capsule may
become loose.
► Fig.22
Cleaning (Suction)
Nozzle
Attach the nozzle to clean off tables, desks, furniture,
etc. The nozzle slips on easily.
► Fig.23: 1. Nozzle
Nozzle + Extension wand (Straight pipe)
The extension wand fits in between the nozzle and the
cleaner itself. This arrangement is convenient for clean-
ing a floor in a standing position.
► Fig.24: 1. Cleaner body 2. Extension wand
3. Nozzle
Corner nozzle
Fit on the corner nozzle for cleaning corners and crev-
ices of a car or furniture.
► Fig.25: 1. Corner nozzle 2. Cleaner body
Corner nozzle + Extension wand
(Straight pipe)
In tight quarters where the cleaner itself cannot
squeeze in, or in high places hard to reach, use this
arrangement.
► Fig.26: 1. Corner nozzle 2. Extension wand
3. Cleaner body
Cleaning without nozzle
You can pick up powder and dust without nozzle.
► Fig.27
For picking up dust on a floor in a standing position, it is
convenient to attach the extension wand to the cleaner.
► Fig.28: 1. Extension wand
MAINTENANCE
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
After use
NOTICE:
Putting the cleaner against the wall
without any other support cause the cleaner to
fall down and be damaged.
► Fig.29
Cleaning
NOTICE:
Never use gasoline, benzine, thinner, alcohol or
the like. Discoloration, deformation or cracks may result.
NOTICE:
Do not blow dust sticking on the
cleaner and filters by air duster. It brings dust into
the housing and causes failure.
NOTICE:
After washing filters, dry them thoroughly
before use. Insufficiently dried filters may cause poor
suction and shorten the service life of the motor.
NOTICE:
After cleaning filters and sponge filter,
be sure to re-install them before use. If you use the
cleaner without filters and sponge filter, dust comes
into the motor housing and cause malfunction.
Cleaner body
From time to time wipe off the outside (cleaner body) of
the cleaner using a cloth dampened in soapy water.
Clean out also the suction opening and filter mounting area.
► Fig.30
High performance filter
Wash the filter in soapy water when it is clogged with dust and the
cleaner power becomes weak. Dry it out thoroughly before use.
► Fig.31
HEPA filter
Optional accessory
NOTICE:
Do not rub or scratch the HEPA filter
with hard objects such as a brush and a paddle.
Clogged HEPA filter cause poor suction performance.
Clean out the filter from time to time.
Occasionally wash the HEPA filter in water, rinse and
dry thoroughly in the shade before use. Never wash the
filter in a washing machine.
► Fig.32
Sponge filter
When the sponge filter becomes dirty, clean it as
follows.
1. Remove the filter.
2. Pull out the sponge filter from between the pillars.
3. Clean the sponge filter by tapping or washing. If
you wash it, dry it out thoroughly before use.
4.
Insert the sponge filter between the pillars and set
it in the original position. Make sure that each bottom
edge of the pillar holds down the sponge filter, and
there is no gap between the sponge filter and suction
opening.
► Fig.33: 1. Sponge filter 2. Bottom edge of pillar
13 ENGLISH