Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Selection Key
4A
For selecting the available welding parameters:
Current, 4B – LED is lit
Wire Speed, 4C – LED is lit
Thickness 0,6-25mm, 4D – LED is lit
Left Display
4
For viewing the parameter selected with key - 4A -
Left Regulation Knob
8
For adjusting the parameter shown in display -- 4 -
Selection Key
5A
For selecting the available welding parameters:
Voltage,
- LED is lit
5B
Arc Voltage Balance,
Right Display
5
For viewing the parameter selected with key - 5A -
9
Right Regulation Knob
For adjusting the parameter shown in display -- 5 -
7
Inductance Regulation Knob
For adjusting the arc dynamics (-10+10).
Press the key – 1 – to get back to the main menù.
Selection Key - Secondary parameters
2
With a prolonged pression of the key - 2 - it is
possible to adjust through the right knob - 9 -, the
value of the following secondary parameters.
CYCLE -
Normal or full cycle
PRE GAS TIME -
Regulation of the gas outflow before
the welding start (0 – 25 sec.)
POST GAS -
Regulation of the gas outflow time at
the end of welding (0 – 25 sec.)
HOT START % -
Percentage of current increase
during hot start phase
HOT START V -
For adjusting the arc voltage com-
pensation during hot start phase
HOT START T -
Time of hot start phase
HOT SLOPE T -
Time required to shift from hot start
phase to welding phase.
CRATER SLOPE -
welding phase to crater fill phase.
CRATER % -
Percentage of current decrease during
crater fill phase
CRATER V -
Adjust arc voltage compensation during
crater fill phase
Turn the Regulation Knob - 8 - to select the parameter
to be adjusted. The left display - 4 - views the
reference number of the parameter:
14
- LED is lit
5C
Time required to shift from
•
P00 = Pre-Gas
•
P03 = Post-Gas
•
P10 = Ciclo
Turn the Regulation Knob - 9 - to select ON
in the parameter 10 and proceed with the
adjustment of the following parameters: :
•
P11 = Hot Start %
•
P12 = Hot Start V
•
P13 = Hot Start T
•
P14 = Hot Slope T
•
P15 = Crater Slope
•
P16 = Crater %
•
P17 = Crater V
The right display - 5 -views the selected parameter
adjusted value.
The LED - 5D - is lit.
Spot Welding Time Regulation Knob
6
Select the Spot Welding through the Selection Key
- 5 -. The corresponding LED is lit. The knob - 6 -
adjusts the maximum duration of pause(0-25 sec).
BBT & Slope of the Motor Regulation Knobs
13
for setting the Burn Back Time and the Slope of the motor.
Note: knobs are located in the wire spool compartment
close to the wire feeding motor.
WIRE SLOPE -
Regulation of time needed to reach
wire set speed after arc striking. Time (0-2.55sec).
BBT -
Regulation of the lenght of the wire protruding
from the torch at the end of welding (1-250ms).
Gas Test and Wire Feed buttons
14
Buttons are located in the wire spool compartment
close to the wire feeding motor (see section "Control
Interface").
TEST GAS -
Allows to check the gas exit.
WIRE FEED -
Allows the wire feed without gas exit.
3
Selection Key
With a short pression it recalls and charges the points
customized by the operator. With a long pression it
saves the parameters adjusted by the operator in the
operator point, LED 5D is lit, the operator point can
be read in the right display - 5 -. Refer to the section
"Save & Recall".
SINERGY - PROGRAM
Selection Key
3
It recalls and charges the sinergy programs saved
in the unit.
•
Hold the key - 3 - until the LED - 5D - lights
up.
•
Turn the right Regulation Knob - 9 - to select the
number of the sinergy program to be recalled.
The right display - 5 - views the number of the
sinergy program.
•
Select the welding program most suitable for
the type of welding going to be performed.
•
To charge the sinergic program press the key
- 3 - or the key - 1 -.
Tabla de contenido
