Description Of Symbols; General Safety - Silverline 633847 Manual Del Usario

Lavadora a presión (gasolina)
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 17
GB

Description of Symbols

The rating plate on your tool may show symbols. These represent important
information about the product or instructions on its use.
Wear hearing protection.
Wear eye protection.
Wear breathing protection.
Wear head protection.
Wear hand protection.
Read instruction manual.
Exhaust gases contain carbon monoxide, a toxic gas. Exposure
to it can provoke loss of consciousness and even death.
Specification
Engine ................................... 97cc
Power .................................... 2.5HP
Fuel ....................................... Petrol
Oil. ......................................... SAE 15W 40
Spark plug ............................. TORCH F6TC
(OR CHAMPION N11YC / BOSCH W8DC)
Spark plug gap ...................... 0.7 - 0.8mm
Fuel tank capacity.................. 1.4L
No load speed ........................ 3600RPM
Working pressure ................... 110 bar
Max pressure ......................... 160 bar
Max flow rate.............................7L/min
Hose length................................5M
Sound power..............................94.99dB (A)
As part of our ongoing product development, specifications of
Silverline products may alter without notice.

General Safety

Carefully read and understand this manual and any label attached to
the tool before use. Keep these instructions with the product for future
reference. Ensure all persons who use this product are fully acquainted
with this manual. Even when used as prescribed it is not possible to
eliminate all residual risk factors. Use with caution. If you are at all unsure
of the correct and safe manner in which to use this tool, do not attempt
to use it.
Keep guards in position
Always keep guards in position, in good working order, correctly
adjusted and aligned. Never attempt to use a tool if any of the supplied
guards are missing. If any guards are damaged, replace before use.
Remove adjusting keys
Always check to see that keys and adjusting devices are removed from
the tool before use.
Clean the work area
Accidents can occur where benches and work areas are cluttered
or dirty. Floors must be kept clear, avoid working where the floor is
slippery. If working outdoors, make yourself aware of all potential slip
and trip hazards before using this tool.
Children and pets
Children and pets should always be kept at a safe distance from the
work area. Lock tools away where children can not get access to them.
Do not allow children, or untrained persons to use this tool.
Use the correct tool
Do not force or attempt to use a tool for a purpose for which it was
4
not designed.
This tool is not intended for industrial use.
Wear suitable clothing and footwear
Do not wear loose fitting clothing, neckties, jewellery, or other items
which may become caught. Wear non-slip footwear, or footwear with
protective toe caps where appropriate. Long hair should be covered
or tied back.
Keep your balance
Do not over reach, keep proper footing at all times, do not use tools
when standing on an unstable surface.
Accessories
The use of any attachment or accessory other than those mentioned
in this manual could result in damage or injury. The use of improper
accessories could be dangerous and may invalidate your warranty.
Secure work
Where possible, always secure work. If appropriate use a clamp or vice,
it will allow you to use both hands to operate your tool.
Check for damaged or missing parts
Before each use, check if any part of the tool is damaged or missing,
check carefully that it will operate properly and perform its intended
function. Check alignment of moving parts for binding. Any guard or
other part that is damaged should be immediately repaired or replaced
by an authorised service centre.
Do not use if defective.
Internal Combustion Safety
Dangerous environment
• Do not use petrol tools in damp or wet conditions, or expose them to rain.
Provide adequate surrounding work space and keep area well lit. Do not
use petrol tools where there is a risk of explosion or fire from
combustible material, flammable liquids, flammable gasses, or dust of
an explosive nature.
Protect yourself from vibration
• Hand held tools may produce vibration. Vibration can cause disease.
Gloves to keep the operator warm may help to maintain good blood
circulation in the fingers. Hand held tools should not be used for long
periods without a break.
Protect your hearing
• Always wear suitable hearing protection when tool noise exceeds 80dB. It
is the responsibility of the user to ensure that other people near to where
the tool is to be used are also suitably protected.
Switch off before connecting
• Ensure that the engine is stopped before connecting any accessories to
the tool. If the tool stops unexpectedly make sure that the engine is not
running before attempting to check the tool.
Running in the engine
• When the tool is new only run the engine at moderate speed
• Do not maintain high engine speed until the engine is fully run in
• The engine will not be capable of developing maximum power until the
end of the running in period.
• When first using the tool, stop and make sure that all nuts and screws
are securely fastened and tighten them as necessary.
• Do not use fuels containing methanol, or ethanol, as these may cause
internal damage to the fuel tank, and fuel lines.
Servicing
• It is recommended that the tool is serviced shortly after its first use.
• In normal use, have the tool serviced regularly.
• Do not attempt to alter any of the components of this tool. To do so
would not only invalidate your guarantee, but may also result in injury to
yourself, or others around you.
• Always have your tool serviced at an authorised service centre.
Storage
• When you have finished using the tool, clean it completely
• Be careful not to hit or cut the fuel tank, or fuel lines, when the tool is
placed on the ground.
• Do not let the tool fall, this could cause damage and may result in the
tool becoming unsafe.
• Store the tool away from direct sunlight
• Ensure that fuel and oil is stored in a safe place, away from heat, direct
sunlight, any source of ignition, and out of reach of children.
Tabla de contenido
loading

Tabla de contenido