Parts & Features - Southland S-WLE-0799 Manual Del Usuario

Edger Specifications
• Save all instructions
Unit Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 lb. (27kg)
Cutting Depths . . . . . . . . . . . . . . . . . . . 0-2.5 in. (0-63 mm)
Blade Diameter. . . . . . . . . . . . . . . . 9 in. (228 mm), 3 point
Gasoline Type . . . . . Regular Unleaded / 88 Octane (min.)
Gasoline Capacity . . . . . . . . . . . . . . . . . . . . . 1.7 qt. (1.6L)
Oil Type (API SG-SL) 10W-30 is recommended for all ser-
vice temperatures. See page 7 for additional information.
Oil Capacity . . . . . . . . . . . . . . . . . . . . . . . . . 12 oz (355 ml)
Spark Plug Model . . . . . . . . . . . . . . . . . . . . . . Torch E7RTC
Parts & Features
1. Start Lever Lever on handle which allows the engine to
run. When lever is released, engine will stop.
2. Choke Control Restricts the air intake. This allows for an
enriched fuel-air mixture which helps to start the engine.
3. Muffler Location of engine exhaust.
4. Adjustable Rear Wheel Right rear wheel is adjustable to
level the edger when edging along a curb (curb-hopping).
5. Adjustable Front Wheel Front wheel is adjustable from
side to side for balance. The front wheel can also adjust
down for curb-hopping.
6. Recoil Starter Handle The engine is equipped with an
easy pull recoil starter.
7. Index Lever Permits adjusting the cutting angle to 15
degrees, 0 degrees (vertical), or -15 degrees. To change
the angle, pull the index lever and rotate the quill assembly
to the desired angle.
8. Blade Rotating cutting element.
9. Blade Guard Prevents stones and debris from being
thrown at the operator.
10. Spark Plug/Spark Plug Wire Provides spark to ignite air/
fuel mixture. The Spark Plug Wire must be disconnected and
moved away from the Spark Plug when servicing the unit.
11. Air Filter Removes debris and contaminates from in-
take air, allowing engine to run smoothly with low exhaust.
12. Depth Selector Plate, 13. Depth Control Lever,
14. Control Rod Used to control the edging depth of cut.
15. Flameout Wire Terminals Must be connected for the
Start Lever to function.
Questions? Call Toll Free at 1-800-737-2112
Spark Plug Gap . . . . . . . . . . . 0.024-0.028 in. (0.6-0.7 mm)
Engine Type . . . . . . . . . . . . . . . . . . . . . . . . . 4 Stroke OHV
Displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79cc
RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3600 RPM
Torque Rating . . . . . . . . . . 3.5 ft-lbs torque per SAE J1940
Bore Diam. x Stroke . . . . . . . . 2.03X1.50 in. (51.6X38 mm)
Intake Valve Clearance . 0.0079-0.0098 in.(0.20-0.25 mm)
Exhaust Valve Clearance . 0.0098-0.012 in.(0.25-0.30mm)
Angle of Ignition . . . . . . . . . . . . . . . . . . . . . . . . 25 Degrees
REAR VIEW
10
FRONT VIEW
1
13
7
12
6
14
15
2
11
4
5
5 Copyright © 2008 MAT Engine Technologies, LLC
Assembly
• Save all instructions
Read and follow the assembly instructions. Do not discard any parts or materials until the unit is assembled.
References to the right or left side of the edger are from the viewpoint of the operator's position behind the edger.
WARNING
Do not operate edger if it is damaged or not completely and correctly assembled.
WARNING
Before doing any assembly or maintenance to the unit, remove the wire from the spark plug.
WARNING
Always wear ANSI compliant safety glasses with side shields while assembling the edger.
The following components will be found in the carton.
Quantities shown in ( ).
1. (1) Edger
2. (1) Edger Operator's Manual
3. (1) Upper Handle
4. (1) Control Rod
5. (1) Container of SAE 30 Engine Oil
6. (1) Parts bag containing the following:
(2) Hair Pins
(2) Plastic Wing Nuts (M8)
(2) M8x35mm Pipe Bolts
(1) Wire Tie
(1) Spark plug socket wrench w/ rod
3
A
How to Remove Edger from Carton
1. Remove all parts and packaging components.
2. Use a utility knife to cut all 4 vertical edges and lay the
side panels flat around the edger.
3. Remove any remaining packaging.
4. Roll the unit out from the carton, and place on a hard
level surface.
B
How to Assemble the Handle
NOTE: Refer to Figure 2 when following steps below:
1. Assemble the upper handle to the lower handle with the
(2) pipe bolts and the (2) plastic wing nuts. Firmly hand-
tighten the wing nuts.
9
8
2. Slide one end of the control rod into the hole of the
Depth Control Lever. Secure with hairpin.
3. Slide the other end of the control rod through the hole of
the quill arm. Secure with second hairpin.
4. Attach the recoil starter handle through the rope guide,
by twisting it into position.
5. Remove the temporary insert from the engine flameout
wire terminal.
6. Connect the flameout wires from the engine and handle.
Figure 1
Use cable tie to secure loose wire to handle.
Questions? Call Toll Free at 1-800-737-2112
If you need assistance or find any parts missing, CALL
TOLL FREE: 1-800-737-2112.
WARNING
DANGER
Flameout wires MUST be connected for correct engine
operation. Failure to connect can result in serious injury.
Hair Pin
Depth Control
Lever
Upper
Handle
Control Rod
Handle
Flameout
Wire
Recoil
Connection
Starter Quill Support
Terminal
Handle
Pipe
Engine
Bolt
Flameout
Wire Hair Pin
Plastic
Wing Nut
Lower
Handle
6 Copyright © 2008 MAT Engine Technologies, LLC
Arm
Figure 2