Idiomas disponibles
Idiomas disponibles
8. Turn power on at main fuse/breaker box.
9. Aim sensor head in desired position.
NOTE: Maintain air spacing between lamps and
sensor head, at least 1 inch. Make sure sensor
head is positioned with control switches facing
towards the ground.
OPERATING YOUR FIXTURE
1. Rotate both knobs on bottom of the sensor to "T"
(test) (Fig. 4).
2. Turn on fixture at wall switch. Allow fixture to warm
up approximately 1 minute before testing. (Light will
come on and stay on during warm-up period.)
3. Readjust sensor head up, down, left, or right until
desired detection area is achieved.
4. Turn sensitivity light knob to desired location. Turn
knob closer to "moon symbol" for light to turn on
(with motion) at night or turn closer to "T" for light
to start detecting motion at dusk (Fig. 5).
NOTE: Make sure you stand motionless while you wait
for the lights to turn off; otherwise the motion sensor
will keep the light fixture on.
5. Once the light fixture goes off, move the time
adjustment controls to the desired length of time.
The floodlight will remain on after the last motion is
detected (5 seconds to 12 minutes) (Fig. 6).
SELECTING YOUR DESIRED FEATURE
Mode of
Operation
"Auto" Setting
(motion activated)
Lights should turn ON with
motion only at night and
on according to the time level
selected by the time
adjustment knob.
Standard Floodlight Setting
Lights should stay ON
continuously both day and night
(must be reset manually).
Test Setting
Lights should turn ON with
motion both day and night.
Lights should turn OFF
after 4 seconds.
TROUBLESHOOTING
Problem
Cause / Solution
Light Does Not
No power to the fixture.
Come On With
• Check if circuit breaker tripped.
• Confirm wall switch is ON.
Motion At Night
Bulb is faulty.
• Replace bulb.
Surrounding external ambient light is too bright. (If so, the unit may
think it is daytime.)
• Re-aim the head.
• Relocate or reposition the unit away from the light.
TURN OFF POWER BEFORE CONTINUING
Wiring to the unit is loose.
• Check wiring and reconnect if necessary using wire
nuts (E) provided.
Fig. 4
Fig. 5
Fig. 6
MODE Knob
How to Set
Adjustment
Power Switch
5 seconds
Keep the power
to
to the fixture ON.
12 minutes
(Any position)
Turn power OFF and turn
power ON once by wall
switch within 2 seconds to
set back to Manual
Override Mode. Turn OFF
for 10 seconds to reset
to Auto Mode.
TEST
Keep the power
(Both knobs at "T")
to the fixture ON.
Problem
Cause / Solution
Light Comes On
There is motion in the detection zone.
For No Apparent
• Make sure the sensor is not picking up moving objects such as
trees, traffic, etc.
Reason At Night
TEST FOR YOURSELF.
• Cover the sensor lens with cardboard to prevent sensor from
detecting motion and cover the photocell on the bottom of the
sensor head. If the light stays off, something in the detection
zone is triggering the sensor.
• Reposition the sensor.
* If the light stays on with the sensor lens covered, contact
customer service.
Light Stays On At
There is motion in the detection zone.
• Make sure the sensor is not in Manual Override Mode.
Night And Does
Not Turn Off
• Make sure the sensor is not picking up moving objects such as
trees, traffic, etc.
• Reposition the sensor.
Light
The light given from the unit's own lamp is affecting the photo
eye in sensor. (Light could be reflecting off of nearby surface.)
Continuously
• Re-aim the lamp.
Blinks On and
• Reposition motion sensor.
Off At Night
Light Is On
The switch on the bottom of the motion sensor is in the test
("T") mode.
During The Day
• Refer to "OPERATING YOUR FIXTURE."
The motion detector is shadowed.
• Reposition motion sensor.
Cannot Activate
Surrounding external ambient light is too bright. (If so, the unit may
think it is daytime.)
Standard
• Re-aim the head.
Floodlight
• Relocate or reposition the unit away from the light.
Setting
Not enough time is allowed to enter the dusk to dawn mode.
(Override)
• Turn power OFF-ON-OFF-ON within 2 seconds.
2-YEAR LIMITED WARRANTY
THE FOLLOWING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES,
WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING, BUT NOT LIMITED TO, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
Cooper Lighting, LLC ("Cooper Lighting") warrants to customers that, for a period of two years
from the date of purchase, Cooper Lighting's products will be free from defects in materials
and workmanship. The obligation of Cooper Lighting under this warranty is expressly limited
to the provision of replacement products. This warranty is extended only to the original
purchaser of the product. A purchaser's receipt or other proof of date of original purchase
acceptable to Cooper Lighting. This is required before warranty performance shall be rendered.
This warranty does not apply to Cooper Lighting products that have been altered or repaired
or that have been subjected to neglect, abuse, misuse or accident (including shipping damages).
This warranty does not apply to products not manufactured by Cooper Lighting which have been
supplied, installed, and/or used in conjunction with Cooper Lighting products. Damage to the
product caused by replacement bulbs or corrosion or discoloration of brass components are
not covered by this warranty.
LIMITATION OF LIABILITY:
IN NO EVENT SHALL COOPER LIGHTING BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES (REGARDLESS OF THE FORM OF ACTION, WHETHER IN CONTRACT,
STRICT LIABILITY, OR IN TORT INCLUDING NEGLIGENCE), NOR FOR LOST PROFITS; NOR SHALL
THE LIABILITY OF COOPER LIGHTING FOR ANY CLAIMS OR DAMAGE ARISING OUT OF OR
CONNECTED WITH THESE TERMS OR THE MANUFACTURE, SALE, DELIVERY, USE, MAINTENANCE,
REPAIR OR MODIFICATION OF COOPER LIGHTING PRODUCTS, OR SUPPLY OF ANY REPLACEMENT
PARTS THEREFORE, EXCEED THE PURCHASE PRICE OF COOPER LIGHTING PRODUCTS GIVING RISE
TO A CLAIM. NO LABOR CHARGES WILL BE ACCEPTED TO REMOVE OR INSTALL FIXTURES.
To obtain warranty service, please contact Cooper Lighting, LLC, at 1-800-334-6871, press
option 2 for Customer Service, or via e-mail [email protected] and
include the following information:
• Name, address and telephone number
• Date and place of purchase
• Catalog and quantity purchase
• Detailed description of problem
All returned products must be accompanied by a Return Goods Authorization Number issued
by the Company and must be returned freight prepaid. Any product received without a Return
Goods Authorization Number from the Company will be refused.
Cooper Lighting, LLC is not responsible for merchandise damaged in transit. Repaired or
replaced products shall be subject to the terms of this warranty and are inspected when
packed. Evident or concealed damage that is made in transit should be reported at once to
the carrier making the delivery and a claim filed with them.
Reproductions of this document without prior written approval of Cooper Lighting, LLC are strictly prohibited.
For assistance, call 1-800-334-6871 or e-mail us at [email protected]
Printed in China
2
