Wireless Device Setup And Pro- Gramming (Hs2Icnrf(P)X/Hs2Lcdrf(P)X) - Tyco DSC PowerSeries neo HS2ICONX Serie Instrucciones De Instalación

Delete Proximity Tags
To delete a prox tag, select the user as outlined previously.Swipe the asso-
ciated prox tag. The alarm system recognizes the tag. Press [*] to delete
when prompted.
LED Bar
On the HS2ICNP/HS2ICNRFP/HS2LCDP keypads, a blue LED bar indic-
ates that a prox tag is approaching.
- The LED bar flashes three times when a valid prox tag is being read by
the keypad.
- If the prox tag is invalid, the LED bar stays on steadily and the keypad
sounds an error tone.
- The brightness of the LED bar is adjustable from the [*][6] menu. When
the backlight brightness is modified, the LED bar brightness is changed
accordingly.
Downloading
The HS2LCDRF/HS2ICNRF products can be programmed over DLS V.
This auto-detects the keypad type and downloads programming accord-
ingly.
Wireless Device Setup and Pro-
gramming
(HS2ICNRF(P)x/HS2LCDRF(P)x)
This section describes how to enroll and program wireless devices such
as contacts, motion sensors and sirens on the alarm panel.
[804][000] Enroll Wireless Devices
1. Once the HSM2HOST is installed and enrolled on the alarm panel
wireless devices can be enrolled using the following method: Enter
Installer Programming section [804][000]:
2. When prompted, either activate the device (see device installation
sheet) to enroll immediately or enter a device ID number. Do the latter to
pre-enroll devices then enroll them later at the customer site.
The alarm panel determines the type of device being enrolled and presents
the appropriate programming options.
Table 4: Wireless Device Options
Device Type Programming Options
(01) Zone type
Zone (02) Partition assignment
(03) Zone label
Wireless key
(01) Partition assignment
(02) User label
Siren
(01) Partition assignment
(02) Siren label
Repeater (01) Repeater label
3. Use the scroll keys or type in the corresponding number to select an
option.
4. Scroll through the available selections, key in a number or enter text as
appropriate.
5. Press [*] to accept and move to the next option.
6. Once all options are configured, the system prompts to enroll the next
device.
7. Repeat the process described above until all wireless devices are
enrolled.
NOTE: The configuration options listed above can be modified using [804]
[911] Modify Device.
[804][001]-[716] Wireless Device Configuration
To configure wireless devices:
1. Enter Installer Programming section [804] then select one of the fol-
lowing sub-sections:
Table 5: Wireless Zone Sub-Sections
Sub-Section Description
001-128 Configure wireless zones
551-556 Configure wireless sirens
601-632 Configure wireless keys
701-716 Configure wireless keypads
2. Select a device to configure using the scroll keys or go directly to a spe-
cific device by entering a hotkey.
3. Use the scroll buttons or enter a hot key to select a configuration option
for the device. See device sheets for details.
4. Press [*] to accept and move to the next option.
5. Once all options are configured, the system returns to the base con-
figuration menu.
Repeat the process described above to configure other wireless devices.
[804][801] RF Jam Detect
RF jam detection (continuous interfering transmissions on the radio net-
work) can be turned on or off. When on, RF jamming is logged and repor-
ted.
To configure RF jamming:
1. Enter Installer Programming section [804][801].
2. Select one of the following options by scrolling or entering the hotkey:
Table 6: Jam Detect Options
Jamming detection and reporting is
00 Enabled/Disabled enabled/disabled Note: Must be Enabled for
UL/ULC listed installations.
01 UL 20/20-USA Continuous RF jamming for 20 seconds
30 seconds of accumulated jamming within
02 EN 30/60-Europe
60 seconds
As EN (30/60) but reported only if the jam-
03 Class 6 30/60-British
ming duration exceeds 5 minutes
3. Press [*] to accept the selection.
4. Press [#] to exit the section.
[804][802] Wireless Supervision Window
This option is used to program the length of time a wireless device can be
absent from the system before a fault is generated.
NOTE: For EN installations, 1 hour or 2 hours must be selected.
When option 06 is used, which configures the system to generate fault con-
ditions after a device has been detected as absent for 24 hours, smoke
detectors generate a fault condition after a maximum of 18 hours when the
200s supervision toggle option is disabled.
To program the Wireless Supervisory Window:
1. Enter Installer Programming section [804][802].
2. Select one of the following options by scrolling or entering the hotkey
Table 7: Wireless Supervisory Window Options
00 Enabled/Disabled
01 After 1 Hour
02 After 2 Hour
03 After 4 Hour
04 After 8 Hour
05 After 12 Hour
06 After 24 Hour
3. Press [*] to accept the selection.
4. Press [#] to exit the section.