Tabla de contenido
Idiomas disponibles
Idiomas disponibles
3. Press [*] to select the module and when prompted, press [*] again to
delete it.
[903][101] Confirm Keypad
To confirm the enrollment of individual keypads and to locate them phys-
ically:
1. Enter [903][101] or use the [<][>] and press [*].
2. Use the [<][>] keys to scroll to the applicable keypad. The module's
serial number and slot number are displayed on the keypad and the status
LEDs on the device flash.
3. To confirm the keypad, press [*]. If communication with a module is
lost at the time of confirmation, a warning message is displayed for 1
second before exiting the section.
Assign a Partition to the Keypad
The keypad must be assigned to a partition if supervision or keypad zones
are required. Keypad assignments and keypad option programming must be
done at each keypad individually.
At each keypad installed on the system:
1. Press [*][8][Installer Code].
2. Enter [861]-[876] for Keypad Programming and Keypad Partition Mask,
corresponding to keypads 1-16.
3. Press [*] for partition assignment.
4. Enter 01 to 08 for partition assignment or use the [<][>] keys to scroll
to the specific partition If partitioning is not used, enter [01]. For Global
keypads, enter [00].
5. Press [#] twice to exit programming.
6. Continue this procedure for each keypad until all have been assigned to
the correct partition.
Program Labels (LCD keypads)
1. Press [*][8][Installer Code].
2. Press [*] and use the [<][>] keys to scroll to Zone Labels and press [*]
again.The first zone is displayed. Alternatively, enter, [000][001].
3. Use the [<][>] keys to scroll to the zone label to be programmed and
press [*] or enter the zone number (e.g., 001, for zone label 1).
4. Use the [<][>] keys to scroll to the desired character's location, using
the [<][>] keys.
5. Enter the number of the corresponding character group until the desired
character is displayed (see the following table). Example, press the "2"
key three times to enter the letter "F". Press the "2" key four times to
enter the number "2". Press [*], then scroll to "Save". Press [*] again to
save the label. To delete a character, use the [<][>] keys to move the
cursor under the character, then press [0]. If any key other than [<][>] is
pressed before [0], the cursor moves one space to the right and deletes that
character.
[1] - A, B, C, 1 [5] - M, N, O, 5 [9] - Y, Z, 9, 0
[2] - D, E, F, 2 [6] - P, Q, R, 6 [0] - Space
[3] - G, H, I, 3 [7] - S, T, U, 7
[*] - Select
[4] - J, K, L, 4 [8] - V, W, X, 8 [#] - Escape
CHANGE CASE – Will toggle the next letter entries between upper case
(A, B, C...) and lower case letters (a, b, c...).
ASCII ENTRY – Used to enter uncommon characters. Valid entries range
from 000 to 255. Use the [<][>] keys to scroll through the characters or
enter a 3-digit number from 000-255. Press [*] to enter the character into
the label.
CLEAR TO END – Clears the display from the character where the cursor
was located to the end of the display.
CLEAR DISPLAY – Clears the entire label.
Continue from Step 2, until all labels are programmed.
Label Library
The Label Library is a database of words commonly used when pro-
gramming labels. Individual words can be combined as needed (e.g., Front
+ Door). Each line of the display supports a maximum of 14 characters. If
a word will not fit on a line, scroll right until the cursor appears at the
first character of the second line and then add the word.
To program a custom label using the Label Library:
1. Press [*][8][Installer Code][000][001].
2. Enter [001] (to program the label for zone 01), or use the [<][>] keys to
scroll to the Zone Labels and then press [*]. The current label name is dis-
played for that zone.
3. Press [*] to open the menu.
4. Press [*] again to select the "Word Entry" option.
5. Enter the 3-digit number corresponding to a word (see Words Library) or
use the [<][>] keys to view words in the library.
6. Press [*] to select the word.
7. To add another word, repeat the previous procedures from step 3.
8. To add a space, press the right scroll key [>].
9. To clear characters, select "Clear to End" or "Clear Display" from the
menu.
10. To save the current label and exit, press [#].
Broadcast LCD Labels
If more than one LCD keypad is present on the system, labels programmed
on one keypad will be broadcast to all other LCD keypads, after the
change is confirmed.
Change Brightness/Contrast/Buzzer
LCD Keypads
1. Press [*][6][Master Code].
2. Use the [<][>] keys to scroll to either Bright Control, Contrast Control,
or Buzzer Control.
3. Press [*] to select one of the following settings:
Brightness/LED Bar Control -15 backlighting levels available.
l
Contrast Control -15 display contrast levels available.
l
Buzzer Control - 15 buzzer control levels available.
l
4. Use the [<][>] keys to scroll to the desired setting.
Keypad Programming
1. Press [*][8][Installer Code].
2. Select one of the programming options identified in the following.
[860] Keypad Slot Number
Not for programming; the two-digit slot number is displayed for inform-
ational purposes only.
[861]-[876] Keypad Programming Sections
[000] Address of Partition
Default: 01
A 2-digit entry is required to assign the keypad to a partition. Valid
entries are 00-32.
NOTE: LED and ICON keypads must not be assigned as global keypads.
[001]-[005] Keypad Function Key Programming
To program a function key:
Press [*][8][Installer Code].
1. Enter [861]-[876] for keypad programming.
2. Enter [001]-[005] for function keys 1-5 or use the [<][>] keys and press
[*].
3. Enter a 2-digit number to assign a function key operation - [00]-[68]. See
the following table.
4. Repeat from step 3 until all function keys are programmed.
5. Press [#] twice to exit Installer Programming.
Table 3: Function Key Assignment
Function
Valid
Button
Default Function
Key
Range
[001]
Key 1
00–68
03
[002]
Key 2
00–68
04
[003]
Key 3
00–68
06
[004]
Key 4
00–68
22
[005]
Key 5
00–68
16
|___|___|
Stay Arm
|___|___|
Away Arm
Chime
|___|___|
ON/OFF
Command
|___|___|
Output 2
|___|___|
Quick Exit
Tabla de contenido
