Tabla de contenido
Idiomas disponibles
Idiomas disponibles
●For tСО suЛsОquОnt Нrв suМtТon pСКsО, usО К Нrв iХtОr. In
case of frequent changes between dry and wet suction-
ТnР, аО rОМommОnН usТnР К sОМonН iХtОr sОt, prОПОrКЛХв
poХвОstОr iХtОr МКssОttОs.
5.3 ClНanСnП tРН iltНr.
TСО suМtТon unТt Тs ittОН аТtС Кn ОХОМtro-mКРnОtТМ iХtОr МХОКnТnР
НОvТМО аСТМС МКn sСКФО oПП Кnв Нust КНСОrОН to tСО ПoХНОН iХtОr
cassettes.
5.3.1 Manual cleaning.
The vibration function (switch setting R or RA /switch
ЛО КМtТvКtОН Кt tСО ХКtОst аСОn tСО voХumО loа НТspХКв
(warning lamp) lights up or when the warning signal sounds or
when the suction output sinks.
5.3.2 Automatic cleaning (automatic vibration).
Filter cleaning is performed (switch setting RA/switch
automatically during the next working break when the minimum
voХumО loа ХОvОХ Тs rОКМСОН.
5.4 Emptying the tank.
Only permitted with dusts with AGW's > 1mg/m³. Switch off
, open snap locks ⑨. Take top section
disconnect plug
suction hose from the tank
5.5 PapНr iltНr baП.
To ТnsОrt or rОmovО tСО iХtОr ЛКР/ОmptвТnР ЛКР, rОmovО tСО top
section
).
To do this, open the side locks ⑨. OnХв usО tСО pКpОr iХtОr ЛКР
for dry suctioning.
5.5.1 InsНrtСnП tРН papНr iltНr baП.
●25 and 50 litre tank PusС tСО lКnРО ovОr tСО suМtТon
opening
Operating the slide valve:
Push the slide valve from inside to the outside
(see marking
) and press from outside through the suction
pipes to the inside again
.
5.5.2 EаcРanПСnП tРН papНr iltНr baП
CКrОПuХХв puХХ tСО lКnРО Пrom tСО suМtТon МonnОМtТons КnН МХosО
tСО lКnРО.
a) should
c
a)
. Empty the tank.
, turn by 180°
Turn on the motor before putting down to ensure that any falling
suspended dust can be suctioned (refer to the graph page 4).
Dispose of the vacuumed material as per the statutory regula-
tions.
6 Cleaning.
Clean the tank and accessories with water. Wipe the top
section
with a damp cloth. Allow the tank and the accessories
to dry.
7 Servicing.
If the suction output of the unit decreases and is not improved
КПtОr tСО iХtОr МКssОttОs
Оmptв КnН tСО pКpОr iХtОr ЛКР
tТmО to ОбМСКnРО tСО iХtОr МКssОttОs
AppХв tСО vТЛrКtТon ПunМtТon to tСО iХtОr МКssОttОs
exchanging them. Use a coin or another similar object to turn the
catch
on the locking bar
and then press the locking bar
КnН ХТПt out tСО iХtОr МКssОttОs
iХtОr МКssОttОs Тn К Нust-prooП pХКstТМ ЛКР КnН НТsposО oП Кs pОr
tСО stКtutorв rОРuХКtТons. InsОrt nОа iХtОr МКssОttОs. FoХН Нoаn
the hood again and exert a little pressure to click it back into
a,
position.
and
IП tСО motor protОМtТon iХtОr
Кn ТnНТМКtТon tСКt tСО iХtОr МКssОttОs КrО
НОПОМtТvО. PХОКsО ОбМСКnРО ЛotС iХtОr МКssОttОs.
АКsС out tСО motor protОМtТon iХtОr unНОr
running water, dry and re-insert.
Note!
Regularly clean the water level sensors
signs of damage.
are cleaned, (assuming the tank
has been exchanged), then it is
.
again before
90° in an anticlockwise direction
backwards. Fold up the hood
. Immediately seal the removed
is soiled, this is
and examine them for
is
7
Tabla de contenido
