LEGRAND 430 572 Manual Del Usario página 6

Explanation of connectors
This section describes the jacks on the back panel of your MONITOR. There are several ways to connect devices.
HDMI INPUT Lets you connect a device, with an HDMI or DVI output.
HDMI (High Definition Multimedia Interface) provides an uncompressed digital connection that carries both video and audio data by
way of an integrated mini-plug cable.
Since HDMI technology is based on Digital Visual Interface (DVI), the jack on the back of your MONITOR is also compatible with DVI
devices.
HDMI Input lets you connect a device, such as a digital cable box, with an HDMI output.
VGA Connect your computer, or other device with a VGA output, to this jack using a15 pin D-sub cable.
Connecting the Monitor Cables to your Computer
You should be sure all cable connections are secure tighten all cable screws.
Shaking and vibration may dislodge cables that are improperly connected.
Route all wiring and cabling away from heat sources and sharp metal edges to avoid damage.
Also, keep the touch screen cable away from sources of electromagnetic and radiofrequency interference.
Testing the Monitor
After connection, turn on the power switch located on the rear (or side) bezel. Before you test your monitor, make sure all cables are
connected properly and routed through the cable management system. Be sure to tighten all cable screws.
To test that the monitor is working properly:
1. Turn on your device
2. Make sure the video image is displayed. If it is not, turn on your monitor. Ensure the LED is blue – red indicates power but no signal.
3. Make sure the video image is centered with in the screen area.
Use the monitor controls to adjust the image, if necessary perform an Auto Config first, then if you wish you can adjust the
horizontal and vertical position, contrast, and brightness to better suit your video card and your personal preference.
Refer to Basic OSD setup for more information on using the on-screen menu to adjust the video display.
Controls and functions
If you cannot locate your remote, you can use the side panel buttons of your monitor to operate many of the monitor's features.
Buttons located on the lower right section of the panel (22" screen) or on the back (32" screen)
4. + : Increases the volume. In the MONITOR menu system, acts like the right arrow button on the remote control and adjusts menu
controls.
5. - : Decreases the volume. In the MONITOR menu system, acts like the left arrow button on the remote control and adjusts menu controls.
6. LED 1: Remote control signal receiver window
7. LED 2: Remote indicator:In red when standby mode, in blue when display.
Use the on-screen buttons to access the OSD menu and to control settings:
1. Power on the LCD monitor.
2. Press source button to accesses the available video input signals, press + or - button to enter the video mode
3. Press MENU button then press +/- button move highlight icon left / right
4. Press SOURCE button to enter the submenu, then press +/- button corresponding to edit,
5. When you are satisfied with the setting, press MENU button to return to the previous menu or exit
Remote control
Ensure the remote control is pointed toward the remote control window on the display.
No obstacles should be placed between the remote control and the remote control window.The effective receiving scope for the signal
is 3 meters to the front of the remote control window.
LED 1 LED 2
POWER On/Off the monitor
PIP Picture in picture
POP Picture out picture
MUTE Switches the sound on or off
^ , V Navigate into menu
MENU Display the main on-screen menu
<, > Navigate into menu
In the on-screen menu, press the ">" button and enter to select on-screen menu items and change menu values,
INPUT Press to display and select the available video source
INFO Press to display information on the monitor screen
P . M Picture mode
S. M Sound mode
EXIT Press the exit button to exit the menu. On VGA Mode, press this button "auto-adjust"
1. POWER Turn the monitor on or off.
2. SOURCE : Accesses the available video input signals
(VGA - HDMI AV1-AV2 -S-VIDEO)
3. MENU : Brings up the MONITOR Main menu. When in the OSD
system, press MENU button to return to the previous menu or exit