Important; Certification; About This Manual; About Your Air Conditioning Recovery/Recycle Service Center - MasterCool 69789 Instrucciones Para El Uso

mixtures of air and R134a have been shown to be combustible at elevated pressures. These mixtures, if ignited, may cause injury or
property damage. Additional health and safety information may be obtained from refrigerant manufacturers.
ATTENTION: Technicians using this equipment must be certified under EPA Section 609 (Environmental Protection Agency).
WARNING: There is the possibility of refrigerant contamination in the refrigerant container or the mobile A/C system being serviced or
refrigerant container. Before recycling use proper equipment such as a refrigerant identifier, if necessary.
NOTE: Use only new refrigerant oil to replace the amount removed during the recycling process. Used oil should be discarded per
applicable federal, state, and local requirements.
The manufacturer shall not be responsible for any additional costs associated with a product failure including, but not limited to, loss of
work time, loss of refrigerant, cross contamination of refrigerant, and unauthorized shipping and/or labor charges.
IMPORTANT: R134a systems have special fittings (per SAE specifications) to avoid cross-contamination with R12 systems. DO NOT adapt
your unit for a different refrigerant — system failure will result.
PERIODICALLY INSPECT AND MAINTAIN REFRIGERANT HOSES AND SEALS TO ENSURE THAT HOSES AND SEALS PREVENT THE ADDITION OF
EXCESS AIR, DUE TO LEAKS, DURING THE RECOVERY PROCESS, WHICH WOULD INCREASE THE NCG LEVEL IN THE RECOVERED REFRIGERANT.

CERTIFICATION

All technicians opening the refrigeration circuit in automotive air conditioning systems must now be certified in refrigerant recovery and recycling
procedures to be in compliance with Section 609 of the Clean Air Act Amendments of 1990. For information on certification call MACS Worldwide at
(215) 631-7020.

ABOUT THIS MANUAL

This manual includes a SAFETY SUMMARY, MACHINE PREPARATION FOR USE, OPERATION procedures, and MAINTENANCE instructions, for your
Air Conditioning Service Center. Anyone intending to use the machine should become familiar with ALL the information included in this manual
(especially the SAFETY SUMMARY) before attempting to use it.
Before operating this machine for the first time, perform all PREPARATION FOR USE instructions. If your new machine is not properly prepared to
perform a service, your service data could be erroneous. In order to properly perform a complete air conditioning service, follow all procedures in the
order presented. Please take the time to study this manual before operating the machine. Then keep this manual close at hand for future reference.
Please pay close attention to the SAFETY SUMMARY and all WARNINGS and CAUTIONS provided throughout this manual.

ABOUT YOUR AIR CONDITIONING RECOVERY/RECYCLE SERVICE CENTER

Your machine incorporates a highly accurate electronic scale for determining charging weights, etc. Other functions can also be performed with
the electronic scale as you will discover during the operating procedures. Either standard or metric units of measure can be selected. Your new
machine has been designed specifically to use R134a, to operate within the objectives of the Montreal Protocol.

WARRANTY

This product is warranted against any defect in materials and/or construction for a period of 1 year from the date of delivery. The warranty consists
of free-of-charge replacement or repair of defective component parts or parts considered defective by the Manufacturer. Reference to the machine
serial number must be included in any requests for spare parts. This warranty does not cover defects arising from normal wear, incorrect or
improper installation, or phenomena not inherent to normal use and operation of the product.
NOTE: Regarding the above, the Manufacturer reminds the Customer that according to international and national laws and regulations in force the
goods are shipped at the sole risk of the latter and, unless otherwise specified in the confirmation of order phase, the goods are shipped uninsured.
The Manufacturer therefore declines any and all responsibility in merit of CLAIMS for damages due to shipping, loading and unloading, and
unpacking.
The product for which repair under guarantee is requested must be shipped to the manufacturer under the customer's exclusive responsibility and
at the customer's exclusive expense and risk. In order to avoid damage during shipping for repairs, the Manufacturer's original packing must always
be used and scale must be locked prior to shipping, refer to Setup on page 7.
The manufacturer declines any and all responsibility for damage to vehicles on which recovery/recycling and recharging are performed if said
damage is the result of unskillful handling by the operator or of failure to observe the basic safety rules set forth in the instruction manual.
The warranty will expire automatically at the end of the twelve month period or whenever one of the following occurs: failure to perform
maintenance; use of improper maintenance procedures; use of unsuitable lubricants and/or tracer fluids; inept or improper use; repairs performed
by unauthorized personnel and/or with non-original spare parts; damage caused by shocks, fires, or other accidental events.
To activate the warranty, mail the attached warranty card.

GENERAL INFORMATION

Machine identification information is printed on the data plate on the rear of the machine (see Figure 1). Overall machine dimensions:
Height: 41.3 inch Width: 23.6 inch Depth: 21.6 inch Weight:
176 lb
Like any equipment with moving parts, the machine inevitably produces noise. The construction system, paneling, and special provisions adopted by
8