Idiomas disponibles
Idiomas disponibles
Turn controls and gas source or tank OFF when
not in use.
If ignition does NOT occur in 5 seconds, turn the
burner controls OFF, wait 5 minutes and repeat
the lighting procedure.
If the burner does not
ignite with the valve open, gas will continue to
flow out of the burner and could accidently
ignite with risk of injury.
Match-Lighting
•
Do not lean over grill while lighting.
•
Open lid. Turn on gas at LP cylinder slowly.
•
Light burners one at a time.
Match Lighting the Main Burners
1.
Place match into match holder (hanging from right
side of the firebox).
2.
Strike the match and position
lit match through the
grates and hold next to the burner.
3.
Push in and turn burner control
knob to SHi.
Continue
to press in on the control
knob until the
burner ignites or up to 5 seconds.
4.
If ignition
does NOT occur in 5 seconds, turn the
burner control
knob OFF, wait 5 minutes for gas to
clear away,
and repeat the lighting
procedure.
Match
Holder
I
I
Match next to
I
I
Burner
Burner
Flame
Check
•
Remove cooking
grates and heat diffusers.
Light
burners, and rotate
knobs from Hi to Low.
You should
see a smaller flame
on Low than you see on Hi.
Perform
a burner flame check on the side burner as
well (if equipped).
Always
check flame
prior to each
use. If only low flame
is seen, then refer to "'Sudden
flame
drop or low flame"
in the Troubleshooting
Section.
Turning
Grill Off
•
Turn all knobs to OFF. Turn LP cylinder
OFF by
turning
the hand-wheel
clockwise
to a full stop.
Igniter
Check
•
Turn gas off at LP cylinder.
Press and hold electronic
ignitor
button.
A "'clicking"
sound should be heard
and spark seen between
the electrode
and burner.
See "'Troubleshooting"
if no click or spark.
Batteries
•
Batteries will deteriorate
over time, especially
in
outdoor
conditions.
This can cause their casings to
leak. Check the condition
of the battery
periodically
before
use. Remove the battery
from the electronic
ignition
before storing your grill.
Valve
Check
•
Important:
Make
sure gas if off at LP cylinder before
checking valves. Knobs lock in OFF position.
To check
valves, first push in knobs and release. Knobs should
spring back. If knobs do not spring back, replace
valve assembly
before using grill. Turn knobs to Low
position
and then turn back to OFF position.
The
valves should turn smoothly.
Hose Check
•
Before each use, check to see if hoses are cut or
worn. Replace damaged
hoses before
using grill. Use
only identical
replacement
part valve / hose /
regulator
as specified
in the Parts List of this Use and
Care Guide.
General
Grill
Cleaning
•
Hood Interior:
Use a strong solution
of detergent
and
water
or a grill cleaner with scrub brush. Rinse and
allow to air dry. Do not apply a caustic grill / oven
cleaner to painted surfaces.
•
Plastic Parts:
Wash with warm
soapy water
and
wipe dry.
•
Do not use citrisol,
abrasive
cleaners,
degreasers
or a concentrated
grill cleaner
on plastic parts.
Damage
to and failure of parts can result.
•
Porcelain Surfaces:
Because of glass-like
composition,
most residue can be wiped away with
baking
soda / water
solution
or specially
formulated
cleaner.
Use nonabrasive
scouring
powder
for
stubborn
stains.
•
Painted
Surfaces: Wash
with mild detergent
or
nonabrasive
cleaner and warm
soapy water.
Wipe
dry with a soft nonabrasive
cloth.
