Fuel Gauge - Milwaukee M12 23GA Manual Del Operador

OPERATION
To reduce the risk of injury, always
WARNING
wear safety goggles or glasses
with side shields. The operator and other people
in the work area must wear eye protection in ac-
cordance with ANSI Z87.1. Eye protection does not
fit all operators in the same way. Make sure the eye
protection chosen has side shields or provides
protection from flying debris both from the front
and sides. The employer is responsible for enforc-
ing the use of eye protection by the operator and
other people in the work area. When required, wear
head protection in accordance with ANSI Z89.1.
To reduce the risk of injury to yourself and others,
test the tool before beginning work each day ac-
cording to the "Required Daily Testing" section.
Remove battery pack and fasteners before leaving
the work area, moving the tool to another location,
or handing the tool to another person. Failure to do
so could result in serious injury.
Do not use this tool for fastening electrical
cables. It is not designed for electric cable
installation and may damage the insulation of
electric cables thereby causing electric shock
or fire hazards.
NEVER wedge or hold back the workpiece contact
mechanism during operation of the tool. Never
attempt to clear a jammed workpiece contact by
grasping the discharge area of the tool. Doing so
could result in serious injury.
To avoid serious injury, do not attempt to prevent
the recoil by holding the tool too firmly against the
work. Keep face and body away from the tool. Dur-
ing normal use, the tool will recoil immediately after
driving a fastener. This is a normal function of the
tool. Grip the handle firmly, let the tool do the work,
and do not place a second hand on top of the tool.

Fuel Gauge

To determine the amount of charge left in the battery,
actuate the lock-off button. The Fuel Gauge will light
up for 2-3 seconds. When less than 10% of charge
is left, 1 light on the fuel gauge will flash 4 times.
To signal the end of charge, 1 light on the fuel gauge
will flash 8 times and the tool will not run. Charge
the battery pack.
If the battery becomes too hot, the fuel gauge lights
will flash in an alternating pattern and the tool will not
run. Allow the battery to cool down.
Operation
1. Grip the handle firmly.
2. Line up the fastener to the workpiece. 3. Press the workpiece contact tip to the workpiece.
4. Push the lock-off button down and pull the trigger
firmly to drive the fastener. WARNING! To avoid
serious injury, do not attempt to prevent the recoil
by holding the tool too firmly against the work.
5. Remove your fingers from the lock-off button and
trigger and remove the tool from the workpiece.
To avoid serious injury, do not at-
WARNING
tempt to prevent the recoil by hold-
ing the tool too firmly against the work. Keep face
and body away from the tool. During normal use,
the tool will recoil immediately after driving a
fastener. This is a normal function of the tool.
Grip the handle firmly, let the tool do the work,
and do not place a second hand on top of the
tool.
Setting the Depth of Drive
The depth of drive can be adjusted to account for
the size of the fastener and the workpiece material.
K n o w w h a t i s b e h i n d y o u r
WARNING
workpiece. A fastener could travel
through the workpiece and out the other side,
striking a bystander and causing serious injury.
Lower the depth of drive to prevent the fastener
from being pushed all the way through the
workpiece.
1. Drive a test fastener.
2. Remove battery pack.
3. WA R N I N G ! A l w a y s
point the tool away from
yourself and others when
making adjustments.
Failure to do so could
result in injury.
4. Turn the depth selector
left or right to increase
or decrease the driving
depth.
5. Repeat until desired depth is reached.
Clearing a Jammed Fastener
Most jams are caused by a fastener or part of a
fastener wedging between the driver blade and the
nail guide. Fastener strips with an incorrect colla-
tion angle or the wrong fastener gauge may cause
continuous jamming. To clear the jam:
1. Remove battery pack.
2. WARNING! Always point the tool away from
yourself and others when installing or removing
fasteners. Failure to do so could result in injury.
3. Remove all fasteners.
4. Use hex wrench (located on side of magazine) to
remove (3) bolts from top
plate.
5. Detach top plate to check for
jammed nail.
6. Remove the fastener and
other debris (use needle-
nose pliers if necessary).
7. Attach top plate and use hex
wrench to re-install (3) bolts.
8. Reload fasteners according
to "Installing/Removing Fas-
tener Strips."
9. Follow the steps under "Re-
quired Daily Testing" before
restarting the work.
5