Sammic TRX-21 Instrucciones página 5

WORK ANGLES OR POSITIONS:
The work angle or position is determined by the
micro-lever assembly (16) located on the arm
support. If the arm (4) is rotated too much and
exits the work area allowed permitted, the
micro-lever stops the turbo-liquidiser. It is
necessary to rotate the arm to the work area
son that the micro (16) is activated and when
pressing start the turbo-liquidiser can be turned
on again.
TYPES OF TOOLS
Rotating blade. Disc 4 edges reinforced absorp-
tion. (19)
Fixed blade with 42 teeth For fine liquidising
(18).
Fixed blade with 30 teeth For intermediate
liquidising (18).
Fixed blade with 21 teeth For liquidising fibrous
products (18).
CLEANING
ATTENTION: Disconnect the turbo-liquidiser
from the mains before handing any internal
components.
Handle the rotating cutting blade (19) and the
fixed blade (18) very carefully because they
have very sharp edges.
Any components in contact with the food must
be cleaned immediately after use, using hot
water and a food-safe detergent. Then rinse
with plenty of hot water and disinfect using an
ethyl alcohol-soaked cloth (90 º).
It is possible to clean and disinfect the rotating
blade (19), the Fixed blade (18) and the fixed
blade support (17) in a dishwasher.
To do so:
- Release the brake (8), and turn the arm (4)
figure 7 to the "tool change" position. s/figure
3
- With the wrench loosen the 3 screws of the
fixed blade support (2). Remove the fixed
blade (18) + fixed blade support (17) assembly
from the arm.
- Separate the Fixed blade (18) from the blade
protector (17) and clean both parts by hand or
in a dishwasher.
- Loosen the fastening screw (20) with the
wrench and remove it. The rotating blade (19)
comes off the bottom of the grooved shaft.
Clean this part by hand or in a dishwasher.
- Clean the rest of the arm (2) and machine with
hot water and a food-safe detergent. Then
rinse with plenty of hot water and disinfect
using an ethyl alcohol-soaked cloth (90 º).
NEVER power clean. DO NOT use abrasive
detergents (nitric acid, neat bleach, etc.) or
stainless steel scourers or scrubbers as they
could cause rusting.
MAINTENANCE
CAUTION
- Before undertaking any cleaning, inspec-
tion or repair work on the turbo-liquidiser,
the machine must be unplugged from the
mains.
- NEVER insert your hand nor any other utensil
in the tool area (1) fig. 7 during the liquidising,
in order to avoid accidents or the deterioration
of the blades.
- Regularly check that the machine safety devi-
ces are working. Check that the micro-lever
(16) that controls rotation works. If you detect
any anomaly, call the SAMMIC authorised
technical service.
- Regularly check the state of the belt. Remove
the cover (3) and verify that it has the correct
tension.
- Regularly inspect the state of the seal of the
rotating blade drive shaft to preserve the leak-
tightness of this area. Every time you loosen
the trailing axle for maintenance you should fit
a new seal.
- Clean the turbo-liquidiser after every use, as
described above.
- Only a SAMMIC authorised technical service
can replace the power cable if this is dama-
ged.
- Machine noise level, while running, at a height
of 1.6 m and a distance of 1 m, less than 70
dB(A). Background noise: 32 dB(A).
Noise when
Noise
empty
Minimum opera-
60 dB
tion speed
Maximum opera-
63 dB
tion speed
TROUBLESHOOTING
• When the arm is in the work position, when
the start button is pressed the turbo-liquidiser
will not start, check that:
- The turbo-liquidiser is correctly connected to
the mains.
- With the turbo-liquidiser disconnected verify
the state of the fuses. They are inside the
electrical box (12).
- Check that the micro-lever (16) of the arm
functions correctly. Also check that the stain-
less steel lever (16) is correctly set to its ori-
ginal position.
- Check that the timer is not in the central
position and that it works correctly.
• The turbo-liquidiser was on and stopped
without pressing any button.
- If you notice that the motor casing (5) is very
hot, maybe the thermal relay of the motor
has been activated. Wait for about 30 minu-
tes until the motor has cooled and try again.
- The arm (4) may have rotated due to not
being properly fixed and has exited the work
area.
- The timer has fulfilled its function and has
stopped the machine.
• The motor turns but not the rotating blade:
- Check the transmission system: the state of
the belt and check pins and pulleys.
OTHER IMPORTANT INFORMATION
This machine is not designed for use by people
(including children) with reduced physical, sen-
sory or mental capabilities or lacking the neces-
sary experience or knowledge, unless they
have received supervision or instructions from a
health and safety expert.
The turbo-liquidiser must not be left running
unsupervised.
The TRX-22 is a 2-speed turbo-liquidiser. Use
the low speed intermittently. On for 30 minutes
with 10-minute breaks
.
Loaded (immer-
sed in water)
66 dB
≤ 80 dB
EN 5