Parametric Equalizer Adjustments - Alpine DVA-9861 Manual De Operación

6
Select the frequency by turning the Rotary
encoder, then press MODE.
Adjustable frequency:
FRONT/REAR/CENTER: 20Hz - 20kHz (in 1/3 octave steps)
SUBWOOFER:
7
Adjust the level (LEVEL) (±9dB 1dB step) by turning
the Rotary encoder, then press MODE.
8
To adjust other frequencies, repeat steps 6 and 7.
9
To adjust other channels, repeat steps 5 to 8.
10
When the setting is complete, press and hold MUTE
for at least 2 seconds.
The unit returns to the normal mode.
• When the speaker is set to the "OFF" mode, the level of the graphic
equalizer for that speaker cannot be adjusted. Refer to "Setting the
Speakers" (page 36).
• Check the playable frequency ranges of the connected speakers
before making the equalizer adjustments. If the speaker's playable
frequency range is 55 Hz to 30 kHz, for example, adjusting the 40 Hz
or 20 Hz band has no effect. Additionally, you may overload and
damage the speakers.
• When graphic EQ is adjusted, the adjustment for parametric EQ
becomes ineffective.
• When the setting is complete, it is recommended to store the setting
contents. For storing, refer to page 43.

Parametric Equalizer Adjustments

The frequency bands of the graphic equalizer are fixed. This makes it
very difficult to correct for undesired peaks and dips at specific
frequencies. The parametric equalizer's center frequency can be tuned
to these specific frequencies. Then, the bandwidth (Q) and level are
fine-tuned, independently, to make the necessary corrections. The
parametric equalizer function is an advanced tool for serious
audiophiles.
1
Check that Defeat mode is off (page 21).
2
Press and hold MUTE for at least 2 seconds.
The audio processor control mode is activated.
3
Select the P-EQ mode by pressing MUTE
repeatedly.
4
Select L+R or L/R by pressing and holding BAND for
at least 2 seconds.
L+R: Sets the same adjustment values for the left and right
channels.
L/R: Different adjustment values can be set for the left and
right channels.
When graphic EQ is adjusted, this setting will be turned off.
20Hz - 160Hz (in 1/3 octave
steps)
5
Select the desired channel by pressing
then press MODE.
When L+R is selected :
FRONT REAR CENTER
When L/R is selected :
FRONT L FRONT R
SUBWOOFER FRONT L
• The speakers display differs, depending on the connected speakers.
6
Press BAND to select the band.
Adjustable bands:
FRONT/REAR/CENTER: 5 bands
SUBWOOFER:
7
Select the frequency by turning the Rotary
encoder, then press MODE.
The adjustable frequency changes according the band.
8
Adjust the band width (Q) by turning the
Rotary encoder, then press MODE.
The band width is adjustable in 6 steps: 0.5/1/2/3/4/5
9
Adjust the level (LEVEL) (±9dB 1dB step) by turning
the Rotary encoder, then press MODE.
10
To adjust other bands, repeat steps 6 to 9.
11
To adjust other channels, repeat steps 5 to 10.
12
When the setting is complete, press and hold MUTE
for at least 2 seconds.
The unit returns to the normal mode.
• When the speaker is set to the "OFF" mode, the parametric
equalizer for that speaker cannot be set. Refer to "Setting the
Speakers" (page 36).
• It is not possible to adjust the frequencies of adjacent bands within 7
steps.
• Check the playable frequency ranges of the connected speakers
before making the equalizer adjustments. If the speaker's playable
frequency range is 55 Hz to 30 kHz, for example, adjusting the 40 Hz
or 20 Hz band has no effect. Additionally, you may overload and
damage the speakers.
• When the parametric EQ is adjusted, the adjustment for graphic EQ
becomes ineffective.
• When the setting is complete, it is recommended to store the setting
contents. For storing, refer to page 43.
or
SUBWOOFER FRONT
REAR L REAR R CENTER
2 bands
39
-EN
,