Tabla de contenido
Idiomas disponibles
Idiomas disponibles
• Unloading Applications
1
UNLOADING ONTO ANOTHER CONVEYOR
DISCHARGE ZONE
(zOna de desCarga)
FLOW
(FlUJO)
(módUlO de zOna ezlOgIC
CONTROLS REQUIREd:
A standard zone stop signal is used to hold load.
Remove the signal to release load.
3
UNLOADING ONTO CHAIN TRANSFER
DISCHARGE ZONE
(zOna de desCarga)
FLOW
(FlUJO)
EZLOGIC® ZONE CONTROLLER
(DIFFUSE SHOWN)
(módUlO de zOna ezlOgIC
[dIFUsO mOstradO]
CONTROLS REQUIREd:
Same as Item #1.
5
END UNLOADING WITH FORK TRUCK
FORK TRUCK
(mOntaCargas)
UNLOADING ZONE
(zOna de desCarga)
FLOW
(FlUJO)
EZLOGIC® ZONE CONTROLLER
(DIFFUSE SHOWN)
(módUlO de zOna ezlOgIC
CONTROLS REQUIREd:
The zone stop control in the discharge zone may be wired to
stop any load entering the zone. The unloading zone feature
may be used to delay the restart of zone #2 until the fork truck
is clear.
OPERATION
• Conveyor Start-Up
Before conveyor is turned on, check for foreign objects that may have been left
inside conveyor during installation. These objects could cause serious damage
during start-up.
After conveyor has been turned on and is operating, check motors, reducers, and
moving parts to make sure they are working freely.
CAUTION! Because of the many moving parts on the conveyor, all personnel in the
area of the conveyor need to be warned that the conveyor is about to be started.
ZONE STOP SIGNAL
(senal de zOna de parada)
TAKE-AWAY
CONVEYOR
(transpOrtadOr)
EZLOGIC® ZONE CONTROLLER (DIFFUSE SHOWN)
®
) [dIFUsO mOstradO]
ZONE STOP SIGNAL
(senal de zOna de parada)
)
®
CHAIN TRANSFER
(transFerenCIa
de Cadena)
) [dIFUsO mOstradO]
®
2
UNLOADING ONTO TURNTABLE
DISCHARGE ZONE
(zOna de desCarga)
FLOW
(FlUJO)
EZLOGIC® ZONE CONTROLLER
(DIFFUSE SHOWN)
(módUlO de zOna ezlOgIC
[dIFUsO mOstradO]
TURNTABLE/CRR MOUNTED
(mesa gIratOrIa / Crr mOntadO)
CONTROLS REQUIREd:
Same as Item #1.
4
UNLOADING ONTO TRANSFER CART
CRR
(zOna de desCarga)
FLOW
(FlUJO)
EZLOGIC® ZONE CONTROLLER
(DIFFUSE SHOWN)
(módUlO de zOna ezlOgIC
[dIFUsO mOstradO]
CONTROLS REQUIREd:
Same as Item #1.
UNLOADING FROM INTERMEDIATE ZONE
6
(MUST BE DESIGNATED UNLOADING ZONE)
FORK TRUCK
(mOntaCargas)
ZONE STOP
SIGNAL
(senal de zOna
de parada)
CONTROLS REQUIREd:
A zone stop signal may be used to stop the product. The unload-
ing zone feature may be used to delay the restart of the upstream
zone until the fork truck is clear.
MAINTENANCE
• Lubrication
The drive chain is pre-lubricated from
the manufacturer by a hot dipping
process that ensures total lubrication of
all components. However, continued
proper lubrication will greatly extend
the useful life of every drive chain.
drive Chain lubrication serves several purposes including:
• Protecting against wear of the pin-bushing joint
• Lubricating chain-sprocket contact surfaces
• Preventing rust or corrosion
9
ZONE STOP SIGNAL
(senal de zOna de parada)
®
)
ZONE STOP SIGNAL
(senal de zOna de parada)
DISCHARGE ZONE
TRACKS
(rIeles)
)
®
TRANSFER CART/CRR MOUNTED
(CarrO de transFerenCIa / Crr mOntadO)
ZONE STOP SIGNAL
(senal de zOna
de parada)
FLOW
(FlUJO)
EZLOGIC® ZONE CONTROLLER
(DIFFUSE SHOWN)
(módUlO de zOna ezlOgIC
) [dIFUsO mOstradO]
®
Ambient Temperature
degrees F
20-40
40-100
100-120
SAE
ISO
20
46 or 68
30
100
40
150
Capítulos
Tabla de contenido
