Safety Precautions - golmar VESTA2 SE GB2 Guía Rápida

VESTA2 SE GB2 MONITOR

SAFETY PRECAUTIONS

- Always disconnect the power supply before installing or making modifications to the device.
- The fitting and handling of these devices must be carried out by
- The wiring must run at least 40 cm. away from any other wiring.
- Do not overtighten the screws on the connector.
- Install the monitor in a dry protected location free from the risk of dripping or splashing water.
- Do not place in humid, dusty or smoky locations, or near sources of heat.
- Before connecting the device to the mains, check the connections between the door panel, power
supply, distributors and monitors.
- Always follow the instructions contained in this manual.
( ) CHARACTERISTICS
*
- Hands-free monitor.
- 4.3" TFT colour screen.
- Monitor with simple installation (non-polarised 2 wire BUS).
- Capacitive buttons to access and select menu functions.
- User menu.
- Installer menu.
- Screen and volume settings menu.
- Start/stop communication button.
- Door release 1 and 2 activation buttons.
- Status LEDs.
- DIP switches for setting the monitor address (call code).
( ) SYSTEM OPERATION
*
- To make a call, the visitor must press the button of the apartment; an audible sound indicates that
the call is being made and LED will turn on. If vocal synthesis is enabled, a 'Call is in progress'
message appears indicating that a call is being made. At this moment, the apartment's monitors
receive the call. If another apartment is called by mistake, press the button for the correct
apartment and the first call will be cancelled.
- The call lasts for 40 seconds and, when received, the image appears on the master monitor
without the visitor knowing. House kit application
'house 1' or monitor with code 16 if the call is in 'house 2') when receiving the call without the
visitor being alerted.
If the call is not answered within 40 seconds, LED
- To establish communication, press button
LED will turn on. If the monitor is a Vesta2 SE GB2/H with icon
the hearing aid is between 15 and 25 cm away from the monitor to ensure maximum audio quality
during communication with the door panel.
- Communication will last for one and a half minutes or until button
communication has finished, LEDs and
synthesis is enabled, a 'Communication is finished' message will indicate that the call is over.
- To open door 1 or 2, press the corresponding button
processes: one press will activate the lock release for five seconds and LED
five seconds. If vocal synthesis is enabled, a 'Door open' message will be indicated on the door
panel.
- A description of the function buttons can be found on page 3.
( )
* For more information, see the TVESTA2 SE GB2 user manual (code
https://doc.golmar.es/search/manual/50120514
authorised personnel .
: the image appears on the monitor (with code 0
will turn off and the channel will be freed.
on any monitor in the apartment. Door panel
on the front, make sure that
is pressed again. When
will turn off and the channel will be freed. If vocal
/ during the call or communication
will also turn on for
50120514)".
2
VESTA2 SE GB2 MONITOR
( ) DESCRIPTION OF THE MONITOR
*
a.
Microphone.
b.
Communication with hearing aids (Vesta2 SE GB2/H).
Sets the hearing aid switch to position T.
c. 4.3" TFT colour screen.
d. Open/close menu button.
e. Menu buttons.
f. Function button door 2 activation
In standby: 'Do not disturb' button/indicator and
'doctor mode' indicator.
g.
Marks for people with a visual disability.
( )
*
Menu buttons and status LEDs:
Menu access and function selection
Menu scroll down button.
In auto switch-on, call or communication: activates the outside light.
Menu scroll up button.
In auto switch-on, call or communication: Selects from the door
panel camera(s) in ascending mode and in carousel (if any).
Menu back button.
( )
*
Monitor address (code) setup:
1-apartment kit 2-apartment kit
APARTMENT 1
APARTMENT 1
VESTA2 SE
VESTA2 SE
CODE 0 CODE 0
( ) 1 2-apartment kit: Monitor code 16 is the last,
DIP 6 of the end of line to ON.
INSTALLATION OF THE MONITOR
( )
*
Location
1.60m
Remember to remove the protective covering from the front of the terminal once installation has been completed.
( )
* For more information, see the TVESTA2 SE GB2 user manual (code
https://doc.golmar.es/search/manual/50120514
EN
a
j
b
c
k
d
l
e
m
f
n
h
j
i
g
h. Function button start/stop communication.
In standby: Display door panel image.
i. Function button door 1 activation.
In standby: Press for 10 seconds to
activate/deactivate the 'doctor mode' function
(function code [9018] must be activated).
. j. Connector fixings.
k. Horizontal cable entry.
l. Connector.
m.
DIP switch.
n. Bus connection terminals.
button.
Power status LED
Button: End call/communication.
In standby: Enter/exit menu mode.
'Do not disturb' function access button.
LED on: 'do not disturb' mode activated.
LED blinking: 'doctor mode' activated.
LED off: function not activated.
Building
APARTMENT 2
DIP 6: Configures the end of line. Leave in the ON position in monitors
where the video cable terminates. Others set to OFF.
VESTA2 SE
DIP 1 to DIP 5: Sets the monitor address (addresses 0 to 31).
The switches set to OFF have a zero value. The values of the switches
set to ON are shown in the table below. The monitor code is the sum of
the values of the switches set to ON.
( )
1 CODE 16
Table of values
Switch number: 1 2 3 4
Value when ON: : 1 2 4
Surface Embedding box
4 30 x
3
ON DIP
1 2 3 4 5 6
.
ON DIP
5
1 2 3 4 5 6
8 16
E xample : 0 + 0+4+0+16 = 20
Screws supplied with the
embedding box.
5012 0514 )".
EN