Safety Precautions; System Operation - golmar Plus Nexa Guía Rápida

VIDEO SYSTEM PLUS NEXA - BUILDING

SAFETY PRECAUTIONS

- Install or modify the equipment, without the power connected.
- The installation and handling of these equipments must be performed by authorised personnel.
- The entire installation must be at least 40 cm.
- With power supply:
Do not use excessive force when tightening the connector screws.
w
Install the power supply in a dry and protected place without risk of drip or water projections.
w
Avoid to place it near to heating sources, in dusty locations or smoky enviroments.
w
Do not block ventilation holes of the unit so that air can circulate freely.
w
To avoid damage, the power supply has to be firmly fixed.
w
To avoid an electrical shock, neither remove the protection cover nor handle the connected wire in the
w
terminals.
( ) CHARACTERISTICS
*
- Audio and video door entry system with simplified installation:
Audio door entry system with 4 common wires installation.
w
Video door entry system with 3 common wires plus coaxial cable installation.
w
Video door entry system with 4 common wires plus twisted pair installation.
w
- Sound module with two operating modes (EL500 or EL501).
- Sound module EL632 Plus P/T with pan and tilt mechanism to adjust the telecamera position.
- Unlimited number of door panels (access) being not necessary the use of switching units.
- Up to 120 monitors / telephones per installation or backbone.
- General door panel (EL501 mode): Up to 120 monitors / telephones, distributed in max. 120 buildings.
- Acoustic busy channel and call acknowledgment signals.
- Visual indications on the door panel for people with impaired hearing: (call and communication process,
door release and busy system).
- EL560 module for video installations with twisted pair cable, integrated in sound module.

SYSTEM OPERATION

- To make a call the visitor should press the push button corresponding to the apartment he wishes to
contact. An acoustic tone will be heard confirming the call is in progress once the push button has been
pressed and the door panel led will turn on
(telephone) in the dwelling. During the call the visitor can correct his call by pressing a push button
corresponding to a different apartment, in which case the original call is cancelled.
- In systems with several accesses doors, the other(s) door panel(s) will be automatically disconnected,if
a visitor tries to call from other door panel an acoustic tone will be heard and the door panel led ...will be
on confirming the system is busy .
- General door panel (EL501 mode): If the call is made from the general door panel, the inner door panel
of the building called and other possible general door panel will remain automatically disconnected, if
another visitor tries to call from an inner busy door panel an acoustic tone will be heard and the door
panel led will be on confirming the system is busy or from another general door panel, an acoustic
tone will be heard confirming the system is busy and
seconds. The door panels of the others inner buildings will remain free to be used.
- General door panel (EL501 mode): In the case that the call is made from an inner door panel, the rest of
inner door panels will remain free to be used. From general door panels only will be able to make calls to
the inner buildings whose door panels are not in use, if the visitor tries to make a call to a busy inner door
panel, an acoustic tone will be heard confirming the system is busy and the
blink for 3 seconds.
- The call lasts for 45 seconds, during which time an image appears on the apartment's monitors for 2
seconds after the call is received without the visitor knowing, and the status LED on the master monitor
will illuminate (green). If the call is not answered within 45 seconds, the master monitor's status LED will
illuminate (red), LED on the door panel will turn off and the channel will be free.
- To establish communication, lift the handset of the monitor (telephone), and the monitor's status LED
(green) and the door panel's LED will illuminate.
- The communication will last for one and a half minutes or until the handset is replaced. After the
communication, the monitor's status LED will illuminate (red), the door panel's LED will turn off and the
channel will be free.
- To open the door, press the door release push button during call or communication progresses: with one
press, the door release operates during 3 seconds. During the lock release activation is activated and
the led will also turn on for 3 seconds.
( ) For more information see manual
*
"T632
https://doc.golmar.es/search/manual/50122328
away from any other installation.
. At this moment the call will be received at the monitor
the general door panel led... will blink for 3
general door panel
/PLUS P/T ML (cod 5012 e 2328 )".
2
VIDEO SYSTEM PLUS NEXA - BUILDING
DOOR PANEL INSTALLATION
( )
*
1650
The push buttons module EL610D must be configured, to assign a call code to the
push buttons. Make this configuration with the dip switch placed in the back side
of the module.
Depending on the setting selected, the push buttons are assigned to a specific call code.
In case to combine these door panels with coded door panels or porter's exchange, it will
be necessary to known the call code of each push button, as shown in the table below.
1
2
3
4
5
6
7
8
9
10
11
12
13
P1- P10: Push button 1 to push button 10.
(1)
Note:Sound module factory set the code "
led will
Important: Select a different configuration option for each module EL610D.
Factory default.
( ) 2
( ) Description and adjustments:
*
- Description of the visual indications on the door panel.
- Description of the door panel led lights (only EL632 Plus module).
- Description of CN8 Bus Nexa connector.
- Description of the SW1 and SW2 configuration dip-switch.
- Description of CN3 function connector.
- Adjustment telecamera position (
( ) ( )
*
3
Operation and programming monitors / telephones.
( )
See the corresponding
3
( ) For more information see manual
*
https://doc.golmar.es/search/manual/50122328
Embedding box dimensions:
Door panel 90CS 90C
Model CE A90C CEV90C
1850
1450
W 99
H 1 3 4 250
D 40
Push buttons module EL-610D
Dip switch Push buttons code
P1 P2 P3 P4 P5 P6 P7
Dip1 Dip2 Dip3 Dip4 Dip5 Dip6 Dip7 Dip8
On Off Off Off Off Off Off On 1 2 3 4 5
Off On Off Off Off Off Off On 11 12 13 14 15
Off Off On Off Off Off Off On 21 22 23 24 25
Off Off Off Off Off Off 31 32 33 34 35
On On
Off Off Off Off On Off Off On 41 42 43 44 45
Off Off Off Off Off On Off On 51 52 53 54 55
Off Off Off Off Off Off On On 61 62 63 64 65
On Off Off Off Off Off Off Off 71 72 73 74 75
Off On Off Off Off Off Off Off 81 82 83 84 85
Off Off On Off Off Off Off Off 91 92 93 94 95
Off Off Off Off Off Off Off
On 101 102 103 104 105
Off Off Off Off On Off Off Off 112 113 114 115 116
Off Off Off Off Off On Off Off 122 123 124 125 126
in P1 and "
, 106" 132"
pan and tilt mechanism an )
monitor / telephone manual .
/PLUS P/T ML (cod 5012 e
"T632
3
90
CEV90
99 mm.
99
328 mm.
56 56 mm.
( ) 2
P8 P9 P10 (1)
6 7 8 9 10 ( ) 2
16 17 18 19 20
26 27 28 29 30
36 37 38 39 40
46 47 48 49 50
56 57 58 59 60
66 67 68 69 70
76 77 78 79 80
86 87 88 89 90
96 97 98 99 100
107 108 109 110 111
117 118 119 120 121
127 128 129 130 131
in P2 .
audio volume.
d
2328 )".