Nolan N104EVO Seguridad E Instrucciones página 10

2 DISASSEMBLY OF THE ROLL NECK
2.1 Remove the rear flaps of the roll neck from their seats on the shell sealing edge as shown in Fig. 12 and in Fig. 15.
2.2 Once the left cheek pad front snap fastener is released, remove the front eyelet fastener as shown in Fig. 11 A.
2.3 Repeat this step on the right side of the helmet.
2.4 Remove the roll neck.
2.5 Hook the cheek pads front snap buttons again (left and right).
3 DISASSEMBLY OF THE LINER
Before removing the liner, remove the roll neck as indicated in the previous paragraph.
3.1 Remove the rear flaps of the liner from their seats on the shell sealing edge as shown in Fig. 13.
3.2 Hold the front left part of the liner and pull it upwards in order to remove the flap from the support fixed to the polystyrene inner
shell (Fig. 14). Repeat the same steps to remove the front central and right flaps.
3.3 Completely remove the liner from the helmet.
4 ASSEMBLY OF THE LINER
4.1 Insert the liner correctly into the helmet and fit it well against the base.
4.2 Insert the left front flap into the seat on the support fixed to the polystyrene inner shell and push it slightly downwards until it is
completely locked (Fig. 14). Follow the same steps for the central front and right flaps.
4.3 Insert the rear flaps of the liner in their lower seats on the shell sealing edge as shown in Fig. 13.
4.4 Carefully adjust the liner until it adheres well to the shell.
NOTE: Check the correct assembly of the liner front area by lifting and lowering the VPS. These movements should be smo-
oth. If this is not the case, repeat the steps 3.2 and 4.2.
5 ASSEMBLY OF THE ROLL NECK
5.1 Insert the rear flaps of the roll neck in their upper seats on the shell sealing edge as shown in Fig. 12 and in Fig. 15.
5.2 Once the left cheek pad front snap fastener is released, hook the front eyelet fastener to the roll neck as shown in Fig. 11 A.
5.3 Repeat this step on the right side of the helmet.
5.4 Hook the cheek pads front snap buttons again (left and right).
6 ASSEMBLY OF THE CHEEK PADS
6.1 Insert the band and the left chin strap into the slot of the left cheek pad.
6.2 Push the padding of the cheek pad in line with the snap fasteners on its back in order to fasten them to their seats (Fig. 11 B).
6.3 Repeat these steps with the padding of the right cheek pad.
2 DISASSEMBLY OF THE ROLL NECK
2.1 Remove the rear flaps of the roll neck from their seats on the shell sealing edge as shown in Fig. 12 and in Fig. 15.
2.2 Once the left cheek pad front snap fastener is released, remove the front eyelet fastener as shown in Fig. 11 A.
2.3 Repeat this step on the right side of the helmet.
2.4 Remove the roll neck.
2.5 Hook the cheek pads front snap buttons again (left and right).
3 DISASSEMBLY OF THE LINER
Before removing the liner, remove the roll neck as indicated in the previous paragraph.
3.1 Remove the rear flaps of the liner from their seats on the shell sealing edge as shown in Fig. 13.
3.2 Hold the front left part of the liner and pull it upwards in order to remove the flap from the support fixed to the polystyrene inner
shell (Fig. 14). Repeat the same steps to remove the front central and right flaps.
3.3 Completely remove the liner from the helmet.
4 ASSEMBLY OF THE LINER
4.1 Insert the liner correctly into the helmet and fit it well against the base.
4.2 Insert the left front flap into the seat on the support fixed to the polystyrene inner shell and push it slightly downwards until it is
completely locked (Fig. 14). Follow the same steps for the central front and right flaps.
4.3 Insert the rear flaps of the liner in their lower seats on the shell sealing edge as shown in Fig. 13.
4.4 Carefully adjust the liner until it adheres well to the shell.
NOTE: Check the correct assembly of the liner front area by lifting and lowering the VPS. These movements should be smo-
oth. If this is not the case, repeat the steps 3.2 and 4.2.
5 ASSEMBLY OF THE ROLL NECK
5.1 Insert the rear flaps of the roll neck in their upper seats on the shell sealing edge as shown in Fig. 12 and in Fig. 15.
5.2 Once the left cheek pad front snap fastener is released, hook the front eyelet fastener to the roll neck as shown in Fig. 11 A.
5.3 Repeat this step on the right side of the helmet.
5.4 Hook the cheek pads front snap buttons again (left and right).
6 ASSEMBLY OF THE CHEEK PADS
6.1 Insert the band and the left chin strap into the slot of the left cheek pad.
6.2 Push the padding of the cheek pad in line with the snap fasteners on its back in order to fasten them to their seats (Fig. 11 B).
6.3 Repeat these steps with the padding of the right cheek pad.
10
10