Kärcher HDS-E 3.3/25-4M Ec Manual Del Usuario página 12

4x blinking
– Heater contactor fault
 Set the appliance switch to "0/OFF".
 Turn on the appliance.
– Error occurs repeatedly.
 Inform Customer Service.
"Low water" indicator lamp
– Lack of water - heater is switched off
 Check water supply, check connections.
Indicator lamp "Ready for use" turns off
– No line voltage, see "Appliance is not running".
Indicator lamp for heater lights up
– Heater operation
Engine indicator lamp
2x blinking
– Engine overload/overheat
 Set the appliance switch to "0/OFF".
 Allow device to cool down.
 Turn on the appliance.
– Error occurs repeatedly.
 Inform Customer Service.
3x blinking
– Fault in the voltage supply.
 Check main connections and mains fuse.
4x blinking
– Excessive power consumption.
 Check main connections and mains fuse.
 Inform Customer Service.
Indicator lamp boiler fault
1x blinking
– Temperature limiter has got triggered.
 Set the appliance switch to "0/OFF".
 Allow device to cool down.
 Turn on the appliance.
– Error occurs repeatedly.
 Inform Customer Service.
3x blinking
– System care detection defective
 Inform Customer Service.
4x blinking
– Temperature sensor defective
 Inform Customer Service.
Indicator lamp service
– Service interval
 Perform service work.
Indicator lamp system care is illuminated
Note: Heater can only operate 5 more hours.
– System care bottle empty.
 Replace the system care bottle.
Indicator lamp system care is blinking
Note: Heater operation no longer possible.
– System care bottle empty.
 Replace the system care bottle.
12
Appliance is not running
– No power
 Check power connection/conduit.
Device is not building up pressure
– Air within the system
Vent pump:
 Set dosing value for detergent to "0".
 With open hand spray gun turn device on and off
multiple times with the device switch.
 Open and close the pressure/quantity regulation at
the pump unit with the hand spray gun open.
Note: By dismantling the high pressure hose from the
high pressure connection the venting process is accel-
erated.
 If detergent tank is empty, refill.
 Check connections and conduits.
– Pressure is set to MIN
 Set pressure to MAX.
– Sieve in the water connection is dirty
 Clean sieve.
 Clean the fine filter; replace it, if necessary.
– Amount of water supply is too low.
 Check water supply level (refer to technical data).
Device leaks, water drips from the bottom of
– Pump leaky
Note: 3 drops/minute are allowed.
 With stronger leak, have device checked by cus-
tomer service.
Note: Condensate can cause increased drop genera-
tion on the appliance.
Device turns on and off while hand spray gun
– Leak in the high pressure system
 Check high pressure system and connections for
tightness.
Device is not sucking in detergent
 Leave the appliance running with open detergent
dosing valve and closed water supply, until the boil-
er is sucked empty and the pressure falls to "0".
 Open the water supply again.
If the pump still is not sucking in any detergent, it could
be because of the following reasons:
– Filter in the detergent suck hose dirty
 Clean filter.
– Backflow valve stuck
 Remove the detergent hose and loosen the back-
flow valve using a blunt object.
Boiler does not heat up
– System care bottle empty.
 Replace the system care bottle.
– Water shortage
 Check water supply, check connections.
– Heater defective.
 Inform Customer Service.
Set temperature is not achieved while using
– Working pressure/flow rate to high
 Reduce working pressure/flow quantity at the pres-
sure/volume regulator in the pump unit.
– 6
EN
the device
is closed
hot water