Draining The Machine - Sammic E-18 Manual Del Usaurio

OPERATION
Starting
1.-Open the 3/4" stopcock to allow water to enter the machine.
2.-Turn on the switch. Turn on the booster pump if one has been incor-
porated to the machine.
3.-Check and make sure that the aspiration filter and the drain plug are
correctly positioned.
4.-Turn the switch control to the (I) position for the automatic filling of
the wash tank and the connection of the heat elements.
Timer
control
Main
switch
Cooling push button
Door handle
Amber lamp
Rinse
aid doser
LVT-19
Main
switch
Door
handle
Start
button
*Cooling push button S-21
Amber lamp
Rinse
aid doser
S-20 / S-21
Tension lamp
Main /drain
switch
Door handle
Ready
lamp
Start button
Cooling
push button
Rinse
aid doser
SB-22
5.-When the machine has reached the washing temperature, introdu-
ce the detergent into the tank (approximately 1/4 full coffee cup at the
beginning of the cycle and same quantity every 5 cycles).
6.-After putting the basket with the glasses, close the door and press
the start botton (LVT-18, LVT-18 A, LVT-18 H, S-20, S-21, SB-22) or
turn lightly the control time clockwise (E-18, E-19 and LVT-19). The
cycle will start automatically.
7.-Some models are equipped with a pushbutton for cooling the glas-
ses and cups after the hot-rinsing process is finished. This cooling
operation continues as long as the pushbutton remains pressed.
Important: Check that the rinsing aid container is filled up. By turning
the timer, 7 or 8 impulses, we will see the filling of the rinsing aid tube
and its going into the boiler. The doser adjustment is made by means
of an adjusting screw.

Draining the machine

Models without draining pump: Take out the drain plug without remo-
ving the filter. Water shall flow away by gravity and dirt shall gather in
the top filter.
SB models: Take out the drain plug without removing the filter and
press the main switch as shown on the operating panel. The draining
pump will go on working while the switch is on, with the door closed.
Tank cleaning
The tank should be cleaned after every washing process:
-Open the door and pull out the drain plug without lifting the filters, in
order to empty the tank and to prevent any large particles from ente-
ring the suction passage of the motor-pump. (Never remove the aspi-
ration filter when the tank is dirty).
-Extract the top filter and clean it carefully.
-SB models: Extract the top filter and the draining pump filter, and
clean it carefully.
-To clean the interior of the wash tank, close the door and start the
machine (after having previously removed the drain plug). In this way,
water will enter via the rinsing dispersers and the machine will clean
itself. This operation should be carried out for 2 to 3 minutes and will
leave the interior of the machine in an almost completely clean condi-
tion.
-Now clean the walls and the interior of the tank in a thorough manner.
The outside of the machine MUST NOT BE washed under a direct
water jet; instead you can use a wet cloth and any ordinary detergent.
OTHER IMPORTANT REMARKS
-Before cleaning, overhauling or repairing the machine, it is necessary
to unplug it from the mains.
-In case of draining pump failure:
1.-Empty the tank, using an adequate container, until the water level is
under the drain plug.
2.-With the drain plug in place, remove the bottom front panel and
change the pump (this can be done without removing the machine
from its location). To empty the machine manually, connect a drain
tube to the sewer. As the drain plug is removed, the tank gets drained
by gravity.
-In the event the power supply cable should get damaged and have to
be replaced, the repair may only be done by a SAMMIC approved
assistance service.
-The emission noise level measured on a typical machine is inferior to
70 dB (A) at a distance of 1 m.
5