Using Your Trail Camera For The First Time - MINOX DTC 1200 Manual De Instrucciones

USING YOUR TRAIL CAMERA FOR THE FIRST TIME

Check scope of delivery
DANGER!
There is a danger of suffocation for children who may play
with the packaging film.
Do not let children play with the packaging film. They can
get caught in it and choke to death.
1. Remove the trail camera out of the packaging and removeall
protective foils.
2. Check whether the delivery is complete
MINOX DTC 1200 Trail Camera
4G antenna
Mounting strap
Micro SD card with adapter
Quickstart guide
Safety instructions
3. Check whether the trail camera or individual parts are dama-
ged. If this is the case, do not use it. Refer to the Quickstart
Guide and contact our service team as indicated.
32 32
Inserting the batteries and memory card
The battery compartment and memory card slot are on the in-
side of the trail camera. (8 | 9)
Opening the trail camera
Release the latch on the side of the trail camera and open it. (2)
Inserting or changing batteries
Before inserting the batteries, make sure that the contacts in
the battery compartment and on the batteries are clean and
intact. Clean them if necessary.
Using non-rechargeable batteries: Use only type LR6 (AA)
batteries.
Using rechargeable batteries:
As an alternative to the type LR6 (AA) batteries, you can use
rechargeable ones in the same size with 2,000 mAh or more.
Recommended are NiMh batteries with a low self-discharge.
Push the "EJECT" button on the bottom edge of the camera
and pull the battery compartment out. (9)
First remove any batteries from the battery compartment.
Insert 12 fully charged batteries. When inserting the batte-
ries, pay attention to the correct polarity, which is indicated
inside the battery compartment for each battery. Eight bat-
teries are inserted at the front of the magazine and four at
the back.
Push the battery magazine back into the slot until it clicks
into place.
When the battery power is low, the low-battery message will
be indicated on display. Please replace all batteries with new
ones.
Check the batteries regularly. Replace old or discharged
batteries.
If you do not intend to use the trail camera for a longer pe
riod of time, remove the batteries to prevent leakage.
Inserting the memory card
Open the trail camera and turn it off. (2 | 7)
Check the write protection on the SD card. If necessary, push
the write protection upwards (towards the gold contacts) to
deactivate the protection.
Carefully push the SD card into the card slot until it audibly
clicks into place. (8)
If you want to take a photo or video and the SD card
is write-protected, you will see "Card protected" in
the display while in SETUP mode. In this case, re-
move the SD card and push the write protection up.
Attention: Always make sure that the write protection of the
SD card is deactivated. Otherwise the trail camera will not
take any pictures.
To remove the SD card, lightly push up on the end of the
card. The SD card will then be partially ejected. Remove the
SD card.
SD/SDHC and microSD/SDHC memory cards with up to 32
GB capacity are supported.
Use only Class 10 memory cards. Cards with a lower speed
can cause errors.
Photos and videos can only be taken if a memory card has
been inserted.
It is recommended to format the memory card before inser-
ting it. Note that any data on the memory card will be dele-
ted during formatting. First back up your data to a computer
Closing the trail camera
WARNING!
The dust and splash water protection is only guaranteed
when the trail camera is completely closed.
Make sure that the trail camera is closed and that the latch
is firmly in place.
Make sure that the protection cap is covering the 6V DC
port. (12)
Pay attention to the correct fit of the seal, which is bordering
the inside of the camera front. If necessary, push the seal
back into the proper position.
Close the camera.
Fasten the latch onto the hooks on the cover. (2)
Push the latch firmly downwards until snug.
Attach a lock (not included in delivery) to the lock hole to
secure the two camera halves. (13)
33 33