Mounting - La Crosse Technology WS-9046U Manual Del Usuario

2. When the alarm time and alarm icon are showing in the DATE LCD
the alarm is activated.
3. When the day and date are showing in the DATE LCD the alarm is
deactivated.
To activate the snooze:
1. While the alarm is sounding press and release the WIND/RAIN/
SNZ button.
2. The snooze will be activated and the alarm will come back on after
the selected time period.

MOUNTING

Note: Before permanently mounting ensure that the indoor weather
station is able to receive WWVB signals from the desired location.
Also, extreme and sudden changes in temperature will decrease the
accuracy of the indoor weather station, and changes in elevation will
result with inaccurate weather forecasting for the next 12 to 24 hours.
These changes will require a 12 to 24 hour wait before obtaining reliable
data. To achieve a true temperature reading, avoid mounting where
direct sunlight can reach the remote temperature/humidity sensor or
indoor weather station. While the remote temperature/humidity sensor
is weather proof, avoid submersion in water or snow. We recommend
that you mount the remote temperature/humidity sensor on an outside
North-facing wall. The sending range is 330ft-obstacles such as walls,
concrete, and large metal objects can reduce the range. Place both
units in their desired location, and wait approximately 15 minutes before
permanently mounting to ensure that there is proper reception. The
indoor weather station should display a temperature and humidity in
the OUTDOOR LCD and wind speed (can be 0.0) in the WIND SPEED
LCD within 4 minutes of setting up.
I. THE REMOTE TEMPERATURE/HUMIDITY SENSOR
The remote temperature/humidity sensor can be mounted in several
ways:
• With the use of screws
• Using adhesive tape
• Using nylon straps
A. MOUNTING WITH SCREWS
1) Remove the mounting bracket from the remote temperature/humidity
sensor.
2) Place the mounting bracket over the desired location.
P.25
GB
3) Place the remote temperature/humidity sensor in your desired
mounting location.
4) Fasten the two nylon straps securely around the mounting location.
II. THE REMOTE WIND SPEED SENSOR
The remote wind speed sensor can be mounted two ways:
• With the use of screws
• Using nylon straps
• With the U-shaped bolt
A. MOUNTING WITH SCREWS
1) Unlock the mounting bracket from the remote wind speed sensor
leaving the wire going through the bracket.
2) Place the mounting bracket over the desired location.
3) Through the two screw holes of the bracket, mark the mounting
surface with a pencil.
4) Screw the mounting bracket onto the mounting surface. Ensure
that the screws are tight against the bracket.
5) Slide the remote wind speed sensor onto the bracket making sure
to lock it in place.
B. MOUNTING WITH NYLON STRAPS
1) Unlock the mounting bracket from the remote wind speed sensor
leaving the wire going through the bracket.
2) Place two nylon straps through the slots on the mounting bracket.
3) Place the remote wind speed sensor in your desired location.
4) Fasten the two nylon straps securely around the mounting location.
5) Slide the remote wind speed sensor onto the bracket making sure
to lock it in place.
P.27
GB
3) Through the two screw holes of the bracket, mark the mounting
surface with a pencil.
4) Screw mounting bracket onto the mounting surface. Ensure that
the screws are tight against the bracket.
5) Insert the remote temperature/humidity sensor into the bracket.
B. MOUNTING WITH ADHESIVE TAPE
1) With a nonabrasive solution, clean and dry the back of the mounting
bracket and the mounting surface to ensure a secure hold. The
mounting surface should be smooth and flat.
2) Remove the protective strip from one side of the tape.
3) Adhere the tape to the designated area on the back of the mounting
bracket.
4) Remove the protective strip from the other side of the tape.
5) Position the remote temperature/humidity sensor in the desired
location, ensuring that the indoor weather station can receive the
signal.
C. MOUNTING WITH NYLON STRAPS
1) Remove the mounting bracket from the remote temperature/humidity
sensor.
2) Place two nylon straps through the slots on the mounting bracket.
C. MOUNTING WITH THE U-SHAPED BOLT
1) Use the U-shaped bolt provided and thread it through each
of the holder holes.
2) Fix the holder to a mast by using the nuts provided.
III. THE RAIN SENSOR (OPTIONAL)
1. Securely mount the rain sensor onto a horizontal surface about 2-
3 ft above the ground and in an open area away from trees or other
coverings. (Rainfall may be reduced causing inaccurate readings.)
2. When securing into place, check that rain excess will not collect
and store at the base of the unit but can flow out between the base
and the mounting surface (test by pouring clean water).
3. After mounting the rain sensor, connect the cable to the thermo-
hydro sensor at the corresponding socket so power supply can be
received and data be transmitted to the base station.
P.26 GB
P.28 GB