Troubleshooting; Maintenance & Care; Specifications; Warranty Information - La Crosse Technology WS-9046U Manual Del Usuario

Idiomas disponibles

Idiomas disponibles

Note: For testing purposes, very slowly pour a small amount of water
into the rain sensor funnel. This simulates the rainfall and rainfall reading
will be received and displayed at the base station for about 2 minute
delay. (to clear this data on the base station, refer to the resetting data
section in "Rainfall Measurement")
IV. THE INDOOR WEATHER STATION
1) Fix a screw (not included) into the desired wall, leaving approximately
3/16 of an inch (5mm) extended from the wall.
2) Place the indoor weather station onto the screw using the hanging
hole on the backside.
3) Gently pull the indoor weather station down to lock the screw into
place.

TROUBLESHOOTING

NOTE: For problems not solved, please contact La Crosse Technology.
Problem:
No reception of WWVB time signal.
Solution:
1) Wait overnight for signal.
2) Be sure indoor weather station is at least 6 feet from any electrical
devices, such as televisions, computers, or other radio-controlled
clocks.
3) Remove batteries for five minutes, reinsert and leave the unit alone
overnight without pressing buttons.
4) If there are still problems, contact La Crosse Technology.
Problem:
Hour is incorrect (minute and date are correct).
Solution:
Be sure correct time zone and daylight saving time settings are selected.
Problem:
The LCD is faint.
Solution:
1) Set the LCD contrast to a higher number.
2) Replace the batteries
Problem:
No outdoor temperature/humidity and/or wind speed is displayed.
Solution:
1) Disconnect the cable from the remote wind speed sensor, then
reinsert making sure the cable clicks in place.
2) Remove all batteries, reinsert into remote temperature/humidity
GB
P.29
Outdoor and dew point: -21.8˚F to 157.8˚F with 0.2˚F resolution
(-29.9˚C to 69.9˚C with 0.1˚C resolution)
"OFL" displayed if outside this range
Wind chill:
-21.8˚F to 157.8˚F with 0.2˚F resolution
(-29.9˚C to 69.9˚C with 0.1˚C resolution)
"OFL" displayed if outside range
Indoor relative humidity
measuring range:
1% to 99% with 1% resolution
("- -" displayed if outside this range
Outdoor relative humidity
measuring range:
1% to 99% with 1% resolution
("- - " displayed if outside this range
Wind speed measuring range:
0 to 111.8 mph (0 to 50 m/s)
Rain Volume Display
(only with Rain Sensor use):
1 hour and 24 hour rainfall: 0
to 999.9 mm with 0.1 mm
resolution (0 to 39 inch with 0.
02 inch resolution)
Total rainfall:
0 to 2499 mm with 0.1 mm resolution
(0 to 98 inch with 0.02 inch resolution)
Weather data checking interval:
Indoor temperature checking interval:
Indoor humidity checking interval:
Outdoor temperature checking interval
(remote temperature/humidity sensor):
Outdoor humidity checking interval:
Wind speed checking interval:
Average of 128 seconds with
highest gust
Outdoor temperature,
humidity and wind speed reception
(indoor weather station):
Transmission range:
330 feet (in open space)
Power Supply:
Indoor weather station:
Remote temperature/humidity sensor:
Remote wind speed sensor:
Supplied by remote temperature/
humidity sensor
Battery life cycle:
Approximately 12 months
Recommended battery type:
Alkaline
Dimensions (H x W x D):
Indoor weather station:
9" x 4.62" x 1.25"
(227 x 117.4 x 31.2 mm)
GB
P.31
sensor first, then the indoor weather station.
3) Place the remote temperature/humidity sensor closer to the display.
4) Be sure all batteries are fresh.
5) Place the remote temperature/humidity sensor and indoor weather
station in position so the straight-line signal is not passing through
more than two or three walls.
Problem:
Temperatures do not match if units are placed next to each other.
Solution:
Each temperature/humidity sensor is manufactured to be accurate to
within 2 degree plus or minus and under normal conditions, so two
sensors could be as much as 4 degrees different. However, the
difference can be exaggerated further because the sensors are
designed for different working environments. The indoor temperature
sensor is less responsive to ambient air currents because of the
shielding effect of the display's case. In addition, the case can act as a
heat sink to absorb and store heat from external sources (i.e. handling
of the case or radiant heat). Also, the much greater range of the remote
temperature/humidity sensor requires a different calibration curve than
the indoor range. Error is usually greater at the extreme ends of a
range, making it harder to compare different ranges with different
curves. Under non-laboratory conditions, it is difficult to compensate
for the above factors and obtain an accurate comparison.
MAINTENANCE AND CARE INSTRUCTIONS
Extreme temperatures, vibration, and shock should be avoided to
prevent damage to the units.
Clean displays and units with a soft, damp cloth. Do not use solvents
or scouring agents; they may mark the displays and casings.
Do not submerge in water.
Immediately remove all low powered batteries to avoid leakage and
damage.
Opening the casings invalidates the warranty. Do not try to repair
the unit. Contact La Crosse Technology for repairs.

SPECIFICATIONS

Weather data measuring range:
Indoor:
Remote temperature/humidity sensor:
Remote wind speed sensor:

WARRANTY INFORMATION

La Crosse Technology provides a 1-year warranty on this weather
station. Contact La Crosse Technology immediately upon discovery
of any defects covered by this warranty.
Before sending the Weather Station in for repairs, contact La Crosse
Technology. The Weather Station will be repaired or replaced with the
same or similar model.
This warranty does not cover any defects resulting from improper use,
unauthorized repairs, faulty batteries, or the Weather Stations inability
to receive a signal due to any source of interference.
LA CROSSE TECHNOLOGY WILL NOT ASSUME LIABILITY FOR
INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR
DA M AG E S A S S O C I AT E D W I T H T H E O P E R AT I O N O R
MALFUNCTION OF THIS WEATHER STATION. THIS PRODUCT IS
NOT TO BE USED FOR MEDICAL PURPOSES OR FOR PUBLIC
Every 15 seconds
INFORMATION. THIS PRODUCT IS NOT A TOY. KEEP OUT OF
Every 20 seconds
CHILDRE'S REACH.
Every 128 seconds
This warranty gives you specific legal rights. You may also have other
Every 128 seconds
rights specific to your State. Some States do no allow the exclusion of
consequential or incidental damages therefore the above exclusion of
limitation may not apply to you.
For warranty work, technical support, or information contact
Every 128 seconds
3 x AA, IEC LR6, 1.5V
2 x AA, IEC LR6, 1.5V
14.2˚F to 139.8˚F with 0.2˚F resolution
(0˚C to 59.9˚C with 0.1˚C resolution) "OFL"
displayed if outside this range
5.4" x 2.25" x 2.25"
(137 x 56.2 x 56.2 mm)
7.5" x 2.2" x 2.2"
(191.2 x 55.8 x 56 mm)
La Crosse Technology
190 Main Street
La Crescent, MN 55947
Phone: 507.895.7095
Fax: 507.895.8000
e-mail:
(warranty work)
(information on other products)
GB
P.30
GB
P.32
loading