Tabla de contenido
Operating Instructions
Protect your eyes and
ears. Wear Z87 safety
glasses, with side
shields. Wear hearing
protection. Employers
and users are responsible for ensur-
ing the user or anyone near the nail-
er wears this safety protection.
Serious eye injury or permanent
hearing loss could result.
Do not use a check
valve or any other
fitting which allows
air to remain in the
nailer. Death or seri-
ous personal injury could occur.
Never place hands or
any other body parts
in the nail discharge
area of the nailer.
The nailer might
eject a fastener
which could result in death or seri-
ous personal injury.
Never carry the nail-
er by the air hose or
pull the hose to
move the nailer or a
compressor. Keep
hoses away from
heat, oil and sharp
edges. Replace any hose that is dam-
aged, weak or worn. Personal injury
or tool damage could occur.
Always assume the nailer contains
nails. Never use the nailer as a toy.
Do not engage in horseplay. Always
keep others at a safe distance from
the work area in case of accidental
discharge of nails. Never point the
nailer at anyone. Accidental trigger-
ing of the nailer could result in
death or serious personal injury.
Nailer Components And Specifications
• REQUIRES: .80 SCFM with 10
nails per minute @ 90 psi
• AIR INLET: 1/4" NPT
• NAIL SIZE RANGE: 3/8" to 1-1/4"
• MAGAZINE CAPACITY:
100 Nails per load, 18 gauge
• WEIGHT: 2 lbs., 9 oz.
• LENGTH: 9"
• HEIGHT: 7"
• MAXIMUM PRESSURE: 100 psi
• PRESSURE RANGE: 50 - 100 psi
Do not drive a
nail on top of
other nails.
The nail could
glance and
cause death or a serious puncture
wound.
Do not operate or
!
allow anyone else
to operate the
nailer if any warn-
ings or warning
labels are not legible. Warnings or
warning labels are located on the
nailer magazine and body.
Never leave the nailer unattended or
connected to an air compressor when
not in use. Serious personal injury
can occur if someone picks up and
uses the nailer without knowing the
correct way to operate the nailer.
Do not drop or throw the tool.
Dropping or throwing the tool can
result in damage that will make the
tool unusable or unsafe. If the tool
has been dropped or thrown, exam-
ine the tool closely for bent, cracked
or broken parts and air leaks. STOP
and repair before using or serious
injury could occur.
Caution indicates a
potentially haz-
ardous situation which, if not avoided,
MAY result in minor or moderate
injury.
Do not modify or alter the nailer or
any nailer parts. Do not use the nailer
if any shields or guards are removed
or altered. Do not use the nailer as a
hammer. Personal injury or tool
damage may occur.
Avoid long extended periods of
work with the nailer. Stop using the
Cap Exhaust
Work Contact
Element (WCE)
2
nailer if you feel pain in hands or
arms.
Always check
that the Work
Contact Element
(WCE) is operat-
ing properly. A
nail could acci-
WARNING
dentally be dri-
ven if the WCE
is not working properly. Personal
injury may occur (see "Checking the
Work Contact Element" Section.)
Disconnect air supply and release
tension from the pusher before
attempting to clear jams because
fasteners can be ejected from the
front of the nailer. Personal injury
may occur.
NOTICE
!
tion, that if not followed, MAY cause
damage to equipment.
Avoid using the nailer when the
magazine is empty. Accelerated
wear on the nailer may occur.
Clean and check all air supply hoses
and fittings before connecting the
nailer to an air supply. Replace any
damaged or worn hoses or fittings.
Tool performance or durability may
be reduced.
Air compressors providing air to the
nailer should follow the require-
ments established by the American
National Standards Institute
Standard B19.3-1991; Safety
Standard for Compressors for
Process Industries. Contact your air
compressor manufacturer for
information.
Warning Labels
Trigger
Nail Loading Area
Nail Discharge Area
Model NB0030
Notice indicates
important informa-
Latch
Magazine
Tabla de contenido
