Genius JA388 Instrucciones Para El Uso página 3

1. WARNINGS
Important: Before attempting any work on the control board
(connections, maintenance), always turn off power.
- Install, upstream of the system, a differential thermal breaker
(Residual Current Device) with adequate tripping threshold.
- Connect the earth cable to the appropriate terminal on the J3
connector of the equipment (see fig.2).
- Always separate power cables from control and safety cables
(push-button, receiver, photocells, etc.). To avoid any electric
noise, use separate sheaths or a shielded cable (with earthed
shield).
2. TECHNICAL SPECIFICATIONS
Power supply
Absorbed power
Motor max. load
Accessories max. load
Electric lock max. load
Operating ambient temperature
Protection fuses
Function logics Automatic / Semi-automatic / "Stepped" safety devices /
Semi-automatic B / Dead-man C / "Stepped" semi-automatic
Opening/closing time
Pause time
Closing leaf delay
Opening leaf delay
Thrust force Dip-switch adjustable on 8 levels for each motor
Terminal board inputs
Opening safety devices / Closing safety devices / Power supply + Earth
Terminal board outputs Flashing lamp - Motors - 24 Vdc accessories power
supply- 24 Vdc indicator-light - Fail safe - 12 Vac electric
lock power supply
Rapid connector
Selectable functions
Opening and closing leaf delay - Reversing stroke -
Fail safe - Closing safety devices logic - Pre-flashing
Programming key
4. ELECTRIC CONNECTIONS
J3
1 2
PE N L
OP
COM
M1
MAIN
C1
M1
230 VAC
50 Hz
NB.: Capacitors are supplied with the operators.
CONTROL BOARD JA388
115 V~ ( +6% -10%) - 50 Hz
10 W
1200 W
0,5 A
15 VA
-20 °C +55 °C
2 (see fig. 1)
Programmable (from 0 to 120 s)
0, 10, 20, 30, 60, 120 s
0, 5, 10, 20 s
2 s (Can be disabled with the dip-switch)
Open / Open free leaf / Stop / Limit-switch
Rapid connector 5 pins
Logics and pause times - Thrust force -
Simple or Advanced work time learning,
with or without Limit-switch and/or encoder
J4
3 4 5 6 7 8
OP
CL
COM LAMP
M2
C2
230 VAC
M2
max.60W
TOTALLY OPEN
OPEN LEAF 1
3. LAYOUT AND COMPONENTS
F1
F1
J3
J3
1 2
PE N L
OP
COM COM
MAIN M1
Led OP_A TOTALLY OPEN LED
Led OP_B LED: OPEN LEAF 1 / CLOSE
Led STOP LED STOP
Led FSWCL LED: CLOSING SAFETY DEVICES
Led FSWOP LED: OPENING SAFETY DEVICES
Led FCA1 LED: LEAF 1 OPENING LIMIT-SWITCH
Led FCC1 LED: LEAF 1 CLOSING LIMIT-SWITCH
Led FCA2 LED: LEAF 2 OPENING LIMIT-SWITCH
Led FCC2 LED: LEAF 2 CLOSING LIMIT-SWITCH
DL10 LED: TIME LEARNING SIGNALLING
J1 LOW VOLTAGE TERMINAL BOARD
J2 RAPID CONNECTOR 5 PINS
J3 230 VAC POWER SUPPLY TERMINAL BOARD
J4 MOTORS AND FLASHING LAMP CONNECTION TERMINAL BOARD
J5 INDICATOR-LIGHT AND ELECTRIC LOCK TERMINAL BOARD
J6 LIMIT-SWITCH AND ENCODER TERMINAL BOARD
F1 MOTORS AND TRANSFORMER PRIMARY WINDING FUSE (F 5A)
F2 LOW VOLTAGE AND ACCESSORIES FUSE (T 800mA)
F TIME LEARNING SELECTION PUSH-BUTTON
DS1 1ST GROUP OF MICROSWITCH PROGRAMMING
DS2 2ND GROUP OF MICROSWITCH PROGRAMMING
J1
9 10 11 12 13 14 15 16 17 18 19
A B CL OP
-
STP
FSW
OPEN
For connection of
the photocells
devices, see
STOP
paragraph 4.1.
1
F2
F2
OP_A
STOP FSWCL
J1
J4
J4 J1
4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
OP A B CL OP
STP -
CL LAMP
M2
OPEN FSW
J6
J5
20 21
+ +
-TX LOCK
- -
+24V FSW W.L.
24 Vdc
3 W
12 V ac
and safety
ENGLISH
DS2
DS1
1 2 3 4 5 6 7 8 9 10 11 12
1 2 3 4
J2
J2
F
F
DL10
DL10
FCC1 FCC2
OP_B
Led
FSWOP
FCA1 FCA2
J6
J6
J5 J5
22 24 25
23
20 21
+ + LOCK
-TX
- -
+24V FSW W.L.
Fig. 1
22
23 24 25
LIMIT-SWITCH
Fig. 2