Precautions For Safety - Toshiba RAS-3M26YAV-E Manual De Instalación

Power supply cord of parts of appliance for outdoor use shall be more than polychloroprene sheathed flexible
cord (Design H07 RN-F), or cord designation 245 IEC 66. (2.5 mm² or more)
UK PLUGS AND SOCKETS ETC (SAFETY) REGULATIONS 1994,
With regard to Schedule 3, item 7 of the above UK Regulations, this appliance must be permanently connected
to the fixed wiring of the main electrical supply by means other than the use of an approved 13 Amp plug-top as
outlined in the Regulations.
Electrical work must be carried by suitably qualified persons and in accordance with all relevant safety stan-
dards and codes of practice.
We recommend that the power supply for this appliance is derived from a suitably protected dedicated circuit.
CAUTION
• THIS AIR CONDITIONER ADOPTS THE NEW HFC REFRIGERANT (R410A) WHICH DOES NOT DESTROY
OZONE LAYER.
R410A refrigerant is apt to be affected by impurity such as water, oxidizing membrane, and oils because pres-
sure of R410A refrigerant is approx. 1.6 times of refrigerant R22. Accompanied with adoption of the new refrig-
erant, refrigerating machine oil has been also changed. Therefore, during installation work, be sure that water,
dust, former refrigerant, or refrigerating machine oil does not enter into the refrigerating cycle of new-refrigerant
air conditioner.
To prevent mixing of refrigerant or refrigerating machine oil, the sizes of connecting sections of charging port of
the main unit or installation tools are different from those for the conventional refrigerant. Accordingly, the
exclusive tools are required for the new refrigerant (R410A) as shown below.
For connecting pipes, use new and clean piping materials with high pressure-tight force, which were made for
R410A only, so that water or dust does not enter. Moreover, do not use the existing piping because there are
problems about pressure-tight force and inner impurity in the existing piping.
CAUTION
This appliance must be connected to the mains by means of a switch with a contact separation of at least 3 mm.
The installation fuse (25A D type
DANGER
• FOR ELECTRICAL WORKS THE WIRING AND CABLES MUST BE PERFORMED IN COMPLIANCE WITH
NATIONAL WIRING STANDARD OR REGULATION.
IF INCORRECT AND INCOMPLETE WIRING IS CARRIED OUT, IT WILL CAUSE AN ELECTRICAL FIRE OR
ELECTRICAL SHOCK.
• USE THE SPECIFIED CABLE (1.0 mm
CONNECTION. CONNECT TIGHTLY AND CLAMP THE CABLE SO THAT EXTERNAL FORCE WILL NOT
BE ACTED ON THE TERMINAL.
• WIRE ROUTING MUST BE PROPERLY ARRANGED SO THAT CONTROL BOARD COVER IS FIXED
PROPERLY.
• DO NOT DAMAGE OR SCRATCH THE CONDUCTIVE CORE AND INNER INSULATOR OF THE CABLES.
• DO NOT DEFORM OR SMASH ON THE SURFACE OF THE CABLES. DO NOT PRESS OR FIX THE CORD
AND CABLES FIRMLY WITH STAPLES, etc.
• DO NOT USE THE INTER-CONNECTING CABLE. NEVER EXECUTE THE CONNECTION OF WIRING
WITH OTHER METHOD THAN THE APPROVED ONE. OTHERWISE, OVERHEAT, SMOKE OR FIRE MAY
BE GENERATED BY CONTACT ERROR.
• TURN OFF MAIN POWER SUPPLY AND BREAKER BEFORE ATTEMPTING ANY ELECTRICAL WORK.
MAKE SURE ALL POWER SWITCHES AND BREAKER TURN OFF. FAILURE TO DO SO MAY CAUSE
ELECTRIC SHOCK.
• CONNECT THE CONNECTING CABLE CORRECTLY. IF THE CONNECTING CABLE IS CONNECTED BY
WRONG WAY, ELECTRIC PARTS MAY BE DAMAGED.

PRECAUTIONS FOR SAFETY

For general public use
New Refrigerant Air Conditioner Installation
To Disconnect the Appliance from the Mains Supply.
) must be used for the power supply line of this air conditioner.
Engage Dealer or Specialist for Installation.
2
or more) AND CONNECT TIGHTLY FOR INDOOR/OUTDOOR
4
SI NUMBER 1768
(for U.K. only)