General Safety - BFT CLONIX1 Instrucciones De Instalación

WARNING! Important safety instructions. Carefully read and comply
with all the warnings and instructions that come with the product
as incorrect installation can cause injury to people and animals and
damage to property. The warnings and instructions give important
information regarding safety, installation, use and maintenance.
Keep hold of instructions so that you can attach them to the techni-
cal file and keep them handy for future reference.

GENERAL SAFETY

This product has been designed and built solely for the purpose indicated
herein. Uses other than those indicated herein might cause damage to
the product and create a hazard.
- The units making up the machine and its installation must meet the
requirements of the following European Directives, where applicable:
2004/108/EC, 2006/95/EC, 99/05/EC and later amendments. For all
countries outside the EEC, it is advisable to comply with the standards
mentioned, in addition to any national standards in force, to achieve a
good level of safety.
- The Manufacturer of this product (hereinafter referred to as the "Firm")
disclaims all responsibility resulting from improper use or any use other
than that for which the product has been designed, as indicated herein,
as well as for failure to apply Good Practice in the construction of entry
systems (doors, gates, etc.) and for deformation that could occur during
use.
- Before commencing installation, check the product for damage.
- Make sure the stated temperature range is compatible with the site in
which the automated system is due to be installed.
- Do not install this product in an explosive atmosphere: the presence of
flammable fumes or gas constitutes a serious safety hazard.
- Disconnect the electricity supply before performing any work on the
system. Also disconnect buffer batteries, if any are connected.
- Before connecting the power supply, make sure the product's ratings
match the mains ratings and that a suitable residual current circuit
breaker and overcurrent protection device have been installed upline
from the electrical system. Ensure that there is an automation, switch
or 16A all-pole thermal magnetic circuit breaker on the grid to enable
complete disconnection in the conditions of overvoltage III category.
- Make sure that upline from the mains power supply there is a residual
current circuit breaker that trips at no more than 0.03A as well as any
other equipment required by code. - Make sure the earth system has been installed correctly: earth all the
metal parts belonging to the entry system (doors, gates, etc.) and all
parts of the system featuring an earth terminal.
- Only use original spare parts for any maintenance or repair work. The
Firm disclaims all responsibility for the correct operation and safety of
the automated system if parts from other manufacturers are used.
- Do not make any modifications to the automated system's components
unless explicitly authorized by the Firm.
- Instruct the system's user on what residual risks may be encountered,
on the control systems that have been applied and on how to open the
system manually in an emergency. give the user guide to the end user.
- Dispose of packaging materials (plastic, cardboard, polystyrene, etc.)
in accordance with the provisions of the laws in force. Keep nylon bags
and polystyrene out of reach of children.
8 - CLONIX/MITTO
INSTALLER WARNINGS
WIRING
WARNING! For connection to the mains power supply, use: a multicore
cable with a cross-sectional area of at least 5x1.5mm
dealing with three-phase power supplies or 3x1.5mm
supplies (by way of example, type H05 VV-F cable can be used with a
cross-sectional area of 4x1.5mm
wires with a cross-sectional area of at least 0.5 mm
- Only use pushbuttons with a capacity of 10A-250V or more.
- Wires must be secured with additional fastening near the terminals (for
example, using cable clamps) in order to keep live parts well separated
from safety extra low voltage parts.
- During installation, the power cable must be stripped to allow the
earth wire to be connected to the relevant terminal, while leaving the
live wires as short as possible. The earth wire must be the last to be
pulled taut in the event the cable's fastening device comes loose.
WARNING! safety extra low voltage wires must be kept physically sepa-
rate from low voltage wires.
Only qualified personnel (professional installer) should be allowed to
access live parts.
SCRAPPING
Materials must be disposed of in accordance with the regulations
in force. Do not throw away your discarded equipment or used
batteries with household waste. You are responsible for taking
all your waste electrical and electronic equipment to a suitable
recycling centre.
ThE dECLARATIoN oF CoNFoRmITY CAN bE vIEWEd oN ThIS WEbSITE:
WWW.bFT.IT IN ThE PRoduCT SECTIoN.
Anything that is not explicitly provided for in the installation ma-
nual is not allowed. The operator's proper operation can only be
guaranteed if the information given is complied with. The Firm shall
not be answerable for damage caused by failure to comply with the
instructions featured herein.
While we will not alter the product's essential features, the Firm reserves
the right, at any time, to make those changes deemed opportune to
improve the product from a technical, design or commercial point of
view, and will not be required to update this publication accordingly.
AVVERTENZE PER L'INSTALLATORE D812160_02
or 4x1.5mm
2
for single-phase
2
). To connect auxiliary equipment, use
2
.
2
when
2