Installation Instructions - Stainless Steel Installation
STEP 1 REMOVE PACKAGING
WARNING
much heavier at the top than at the bottom – be careful
when moving. When using a hand truck, handle from
side only.
AVERTISSEMENT
basculement Le produit est beaucoup plus lourd
en haut qu'en bas. Il faut être prudent lors des
déplacements. Si un diable est utilisé, il faut soulever le
réfrigérateur sur le côté seulement.
ADVERTENCIA
producto es mucho más pesado en su parte superior que
en su parte inferior – tenga cuidado al moverlo. Al usar
un carro manual, sosténgalo de costado únicamente.
• Carefully cut banding at the top and bottom, remove
outer carton.
STEP 2 INSTALL WATER LINE
WARNING
Connect to potable water supply only.
A cold water supply is required for automatic icemaker
operation. The water pressure must be between 40
and 120 psi (275-827 kilopascals).
WARNING
ELECTRIC SHOCK HAZARD
Attach tubing clamp using existing hole only. DO NOT
drill into the refrigerator.
AVERTISSEMENT
Raccordez l'appareil à une
alimentation d'eau potable seulement. Une alimentation
d'eau froide est requise pour faire fonctionner
la machine à glaçons et le pichet à remplissage
automatique. La pression d'eau doit se situer entre 40 et
120 psi. (275 à 827 kPa).
AVERTISSEMENT
Fixez le collier de serrage dans le trou présent seulement.
NE PERCEZ PAS dans le réfrigérateur.
ADVERTENCIA
Realice la conexión a un
suministro de agua potable únicamente. Se requiere
un suministro de agua fría para el funcionamiento de la
máquina de hielos automática y de la jarra de llenado
automático. La presión del agua deberá estar entre 40 y
120 p.s.i. (275 – 827 kPa).
ADVERTENCIA
Adhiera la abrazadera de la tubería usando el agujero
existente únicamente. NO perfore el refrigerador.
Tip Over Hazard. Product is
Risque de
Riesgo de Caída El
RISQUE DE DÉCHARGE
ÉLECTRIQUE
PELIGRO DE DESCARGA
ELÉCTRICA
• Slide out back corner posts (2).
• Slide carton off top of cabinet.
NOTE: IT IS NOT NECESSARY TO
LAY CABINET DOWN IN ORDER
TO REMOVE SKID!
NOTE: DO NOT ATTEMPT TO
ROLL UNIT OFF SKID.
• The unit is secured to the skid with
4 slotted tie-down straps. Remove
the four 5/16" bolts from the base
channels in the tie-downs.
• Remove toekick and wall bracket.
Set aside for final installation.
• Lift the unit off the skid with an appliance dolly. Handle
from the sides.
• Remove the four 7/16" bolts securing the tie-down
brackets to the skid.
• Route 1/4" OD copper or SmartConnect
between house cold water line and the water connec-
tion location.
• Tubing should be long enough to extend to the front of
the unit. Allow enough tubing to accommodate bend
leading into the water line connection.
NOTE: The only Monogram approved plastic tubing is
supplied in the SmartConnect
Do not use any other plastic water supply line because
the line is under pressure at all times. Other types of
plastic may crack or rupture with age and cause water
damage to your home.
SmartConnect
Refrigerator
™
Tubing Kits are available in the
following lengths:
2' (.6 m)
WX08X10002
8' (2.4 m)
WX08X10006
15' (4.6 m) WX08X10015
25' (7.6 m) WX08X10025
Shut off the main water supply.
Turn on the nearest faucet long enough to clear the line
of water.
• Install a shut-off valve between the icemaker water
valve and cold water pipe in a basement or cabinet.
The shut-off valve should be located where it will be
easily accessible.
30
plastic tubing
™
Refrigerator Tubing kits.
™
31-1000416 Rev. 0