Tabla de contenido
Idiomas disponibles
Idiomas disponibles
The Laundry Center canbeinstalled using t hestandpipe drain
system (floor o rwall), thelaundry tubdrain system, orthefloor
drain system. Select thedrain hose installation method youneed.
See "Alternate Parts."
Standpipe
drain system - wall or floor (views A & B)
The standpipe drain requires a minimum diameter standpipe
of 2" (50 mm). The minimum carry-away capacity can be
no less than 17 gal. (64 L) per minute. A 2" (50 mm) diameter
to 1" (25 mm) diameter standpipe adapter kit is available. See
"Alternate Parts."
The top of the standpipe must be at least 39" (990 mm) high and
no higher than 96" (2.4 m) from the bottom of the washer.
39" [
(990
B
Laundry tub drain system
(view C)
The laundry tub needs a minimum 20 gal. (76 L) capacity. The top
of the laundry tub must be at least 34" (864 mm) above the floor
and no higher than 96" (2.4 m) from the bottom of the washer.
Floor drain system (view D)
The floor drain system requires a siphon break that may be
purchased separately. See "Alternate Parts."
The siphon break must be a minimum of 28" (710 mm) from
the bottom of the washer. Additional hoses might be needed.
C
D
It is your responsibility
•
To contact a qualified electrical installer.
•
To be sure that the electrical connection is adequate and in
conformance
with the National Electrical Code, ANSl/NFPA
70-latest edition and all local codes and ordinances.
A copy of the above code standards can be obtained from:
National Fire Protection Association, One Batterymarch
Park,
Quincy, MA 02269.
To supply the required 3 or 4 wire, single phase, 120/240 volt,
60 Hz., AC only electrical supply (or 3 or 4 wire, 120/208 volt
electrical supply, if specified on the serial/rating
plate) on a
separate 30-amp circuit, fused on both sides of the line. A
time-delay fuse or circuit breaker is recommended.
Connect
to an individual branch circuit. Do not have a fuse in the
neutral or grounding circuit.
Do not use an extension cord.
If codes permit and a separate ground wire is used, it is
recommended
that a qualified electrician determine that the
ground path is adequate.
Electrical
Connection
To properly install your Laundry Center, you must determine the
type of electrical connection you will be using and follow the
instructions
provided for it here.
•
This dryer is manufactured
ready to install with a 3-wire
electrical supply connection. The neutral ground wire is
permanently connected to the neutral conductor
(white wire)
within the dryer. If the dryer is installed with a 4-wire electrical
supply connection, the neutral ground wire must be removed
from the internal ground connector (green screw), and
secured under the neutral terminal (center or white wire) of
the terminal block. When the neutral ground wire is secured
under the neutral terminal (center or white wire) of the
terminal block, the dryer cabinet is isolated from the neutral
conductor.
•
If local codes do not permit the connection of a neutral
ground wire to the neutral wire, see "Optional 3-wire
connection"
in "Electrical Connection"
section.
•
Use a 4-wire conductor
cord when the dryer is installed in
a mobile home or an area where local codes do not permit
grounding through the neutral.
If using a power supply cord:
•
Use a UL listed power supply cord kit marked for use with
clothes dryers. The kit should contain:
•
A UL listed 30-amp power supply cord, rated 120/240 volt
minimum. The cord should be type SRD or SRDT and be at
least 4 ft (1.22 m) long. The wires that connect to the dryer
must end in ring terminals or spade terminals with upturned
ends.
•
A UL listed strain relief.
7
Capítulos
Tabla de contenido
Solución de problemas
