Storage; After Each Use; Long Term Storage; Winter Storage - Craftsman 580.768323 Manual Del Operador

Tabla de contenido
Idiomas disponibles

Idiomas disponibles

AFTER EACH USE

Water should not remain in the unit for long periods of
time. Sediments or minerals can deposit on pump
parts and "freeze" pump action. Follow these
procedures after every use:
Flush detergent siphoning tube by placing the filter
into a pail of clean water while running pressure
washer in low pressure mode (adjustable nozzle in
the forward position). Flush for one to two minutes.
Shut off the engine and let it cool, then remove all
hoses.
Disconnect spark plug wire from spark plug.
Empty the pump of all liquids by pulling recoil
handle about 6 times. This should remove most of
the liquid in the pump.
Coil the high pressure hose and inspect it for
damage. Cuts in the hose or fraying could result in
leaks and loss of pressure. Should any damage be
found, replace the hose. Do Not attempt to repair a
damaged hose. Replace the hose with the genuine
Craftsman part.
Disconnect hose from gun and high pressure outlet
on pump. Drain water from hose and wipe off the
hose with a rag.
Slide one end of the hose into the hole on the hose
reel. Turn the hose reel with the handle to coil the
hose onto the reel. Push the other end of the hose
into the clip on the side of you unit.
Reconnect spark plug wire to spark plug.
Store unit in a clean, dry area.
DANGER: Never store the engine with fuel in
the gas tank indoors or in enclosed, poorly
ventilated areas where fumes may reach an
open flame, a spark, or pilot light.

WINTER STORAGE

CAUTION: You must protect your unit from
freezing temperatures. Failure to do so will
permanently damage your pump and render
your unit inoperable.
To protect the unit from freezing temperatures:
Flush detergent siphoning tube by placing the filter
into a pail of clean water while running pressure
washer in low pressure mode (adjustable nozzle in
the forward position). Flush for one to two minutes.
Disconnect hose connected to chemical inject
fitting on the pump.
Empty the pump of all pumped liquids by pulling
recoil handle about 6 times. This should remove
most of the liquid in the pump.
Connect a 3-foot section of garden hose to the
water inlet adapter. Pour RV–antifreeze (antifreeze
without alcohol) into the hose. Pull the recoil handle
twice. Disconnect 3-foot hose.

STORAGE

LONG TERM STORAGE

If you do not plan to use the pressure washer for more
than 30 days, you must prepare the engine for long
term storage.
It is important to prevent gum deposits from forming in
essential fuel system parts such as the carburetor, fuel
filter, fuel hose or tank during storage. Also,
experience indicates that alcohol-blended fuels (called
gasohol, ethanol or methanol) can attract moisture,
which leads to separation and formation of acids
during storage. Acidic gas can damage the fuel
system of an engine while in storage.
Protect Fuel System
Fuel Stabilizer:
If adding a fuel stabilizer, fill the fuel tank with fresh
gasoline. If only partially filled, air in the tank will
promote fuel deterioration during storage.
Add fuel stabilizer following manufacturer's
instructions.
Make sure you have water supply to pump inlet
connected and turned ON.
Run the engine outdoors for 10 minutes to be sure
that treated gasoline has replaced the untreated
gasoline in the carburetor.
Change Oil
While engine is still warm, drain oil from crankcase.
Refill with recommended grade. See "Changing Oil" on
page 14.
Oil Cylinder Bore
Make sure control lever is in stop position. Remove
spark plug. Squirt about 1 tablespoon of clean
engine oil into the cylinder. Cover spark plug hole
with rag. Pull recoil handle slowly to distribute oil.
Avoid spray from spark plug hole.
Install spark plug. Do Not connect spark plug wire.
OTHER
Do Not store gasoline from one season to another.
If possible, store your unit indoors and cover it to
give protection from dust and dirt. BE SURE TO
EMPTY THE FUEL TANK.
Draining Fuel Tank:
DANGER: Drain fuel, using a funnel, into
approved container outdoors, away from open
flame. Be sure engine is cool. Do Not smoke.
Remove the float bowl bolt, then rotate the fuel
valve lever to the "ON" position.
After all fuel has drained into the container, reinstall
the float bowl bolt while holding the float bowl in
position on the carburetor. Tighten bolt securely.
IMPORTANT: NEVER cover your pressure washer
while engine and exhaust area are warm.
16

Capítulos

Tabla de contenido
loading

Tabla de contenido