Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
®
Y25
2-Cycle
Trimmer
Operator'
Removing UnitFrom Carton
Remove all contents
from
carton.
Assemble The Unit
Bracket
]
L
]
No Tools Required!
Starter
Rope
On/Off
Switch
Slide shield's slot onto
mounting
bracket.
Rotate
shield onto shaft. Push
square
bolt through shield
and bracket. Tighten
washer
and wing
nut
onto bolt.
Put D-handle on shaft. Move
handle a minimum 6 inches
away from shaft grip. Insert
clamp bolt and tighten the
wing nut.
D-Handle
Throttle
Control
Assemble The Unit
f
1 Gallon
3.2 oz
1
J
E]
Mix thoroughly
in separate
fuel can:
-
3.2 ft. oz. of 2-cycle
engine
oil
-
1 galmon of unleaded
gasoline
NOTE: Do not mix directly in
fuel tank.
Place unit on a level
surface. Fill fuel tank.
]
Starting The Unit
_rimer
'=fr ACL"
L
Bu_
......
]
10X
Press primer bulb 10 times,
or until fuel is visible
1--
Choke
Lever
i
Move choke lever to
Position
1.
]
Need Help?
Call 1-800-800-7310
DIDN'T
START?
Repeat these instructions.
IF engine fails to start after2
attempts,
move choke lever to position
3 and pull
the starter rope until engine starts
IF unit still fails to start, refer to the
operator's
manual for additional
starting
and troubleshooting
information
Starting The Unit
[--1
Crouch
in starting
position.
SQUEEZE
and HOLD
throttle for ALL further
steps.
Pull rope 5 times.
]
j
Move choke lever to
Position
2 and squeeze
throttle.
]
:
35xj
F]
Pull rope 34 times
to start
engine. Run unit for 30-60
seconds
to warm up.
r
E
Choke Lever
Continue
to squeeze
throttle.
Move choke lever
to Position
3.
]
Continue
to squeeze
throttle.
Run unit for an
additional
60 seconds
to
complete
warm-up.
Unit
may be used during this
time.
n
I
,,C
_m
C
uJ
m
m
LO
n
I
C
U,
m
Reloading The Line*
Bend short end and push it
into the other hole. Pull tight.
E]
insert 10' of 0,080"
SplitLine ® through hole in top
of reel. Pull most of line
through hole until 3"-4"
remains.
Replacement
SplitLine c_ :
Part #49U0134K953
For single line installation, refer to Line Installation
section of this manual
j
)
J
Wind line tightly in direction
Push 6"-7" ends into 0.080"
Insert or slide lines into the
Pull lines firmly to release
of arrow. Split other end of
holding slots,
eyelets in spool. Insert spring
from holding slots.
®
SplitLine
back 6"-7".
and reel into spool.
F]
O
n
I
m
O
_C
o_
¢0
uJ
f
_
SP oolE
Spring
_
nner
Reem
Unscrew
bump
knob
counterclockwise.
Remove
inner reel and spring.
Reloading The Line
Hold the inner reel in place.
Tighten Bump Knob
clockwise.
f
For replacement
spool installation, refer to
Installing a Prewound Reel section of this manual.
*This is to assist
in the reloading
of Splitline®
only. These instructions
are NOT part of the fast assembly
instructions.
Line does not need to
be installed
on the initial
assembly
and start-up.
NEED HELP?
CALL 1-800-800-7310
iN U.S. OR 1-800-668-1238
iN CANADA
PART NO. 769=06169
P00
(6/10}
