Tabla de contenido
Idiomas disponibles
Idiomas disponibles
PRELIMINARY SUGGESTIONS
•
The installation must be done by a technician following the
safety norms in force.
•
Only apply to authorized personnel to replace the feeding
cable of the motor.
•
Do not pierce nor insert screws in the whole length of the
motor.
•
Avoid any contact of the motor with liquids.
•
Avoid to crush or knock over the motor.
•
Possible tampering or wrong connections are not covered by
guarantee.
INSTALLATION WARNING:
1. If a manual release is provided, the actuating member is to
be installed at a height less than 1,8m.
2. Before installing the drive, remove any unnecessary cords and
disable any equipment not needed for powered operation.
3. For installation for awnings, a horizontal distance of at least
0,4m is to be maintained between the fully unrolled driven
part and any permanent object.
4. The power supply cable should not be exposed to sunlight or
rain directly.
5. If the driver part is awnings, a horizontal distance of a least
0,4 m is to be maintained between the fully unrolled driven
part and any permanent object.
Note:
a) Please read the instruction carefully before installation.
b) Assure that all accessories have been fixed so that the motor
works without any mechanical problem. The loading weight
should be matched with the output power of the motor.
c) Electrical connection must be done by professional
technicians to operate in conformity with the rules.
WARNING: Important safety instructions. It is important for the
safety of persons to follow these instructions. Save these
instructions.
WARNING: Important safety instructions.
•
Follow all instructions, since incorrect installation can lead to
severe injury.
•
Do not allow children to play with fixed controls.
•
Keeps remote controls away from children.
•
Frequently examine the installation for imbalance and sings
of wear or damage to cables and springs.
•
Do not use if repair or adjustment is necessary.
•
Moving parts of the drive must be installed higher than 2.5
m above the floor or other level that could provide access to it.
•
Before installing the drive, remove any unnecessary cords and
disable any equipment not needed for powered operation
•
Install the actuating member of a manual release at a height
less than 1.8 m.
•
The actuating member of a biased-off switch is to be located
within direct sight of the driven part but away from moving
parts. It is to be installed at a minimum height of 1.5 m.
•
Fixed controls have to be installed visibly.
•
Having worked 4 min later, the appliance can not restart until
the temperature of the appliance reach to ambient
temperature.
•
The appliance can not be used in outside.
INSTALLATION
•
Fix the stirrup
to the wall.
•
Insert the crown
in the driving wheel
(fig.1).
•
Insert the pulley
on the pivot of the motor
•
Insert the copper pin
•
ONLY for the models with emergency handling:
- Put the eyelet
in the hole
- Fix the eyelet with the screw
•
Insert completely the motor in the roll-tube (fig.2).
•
Fix the roll-tube to the driving wheel with m 4 x10 screw
(fig.2).
Electric connections
•
Operators must be installed with a bipolar switch with a
minimum contact clearance opening distance of at least 3mm
(fig.3).
•
Do not connect more than one motor for every push-button of
command.
•
Reverse the brown and black cables, in order to change the
direction of revolution (fig.3)
Limit switch adjustment
•
The limit switches system is electromechanical and through a
micro-switch it interrupts the feeding of the motor when the
roller shutter or the awning reaches the limit of opening and
closing.
•
The limit switches are pre-adjusted to approximately 5 crown
revolutions.
•
To adjust the opening and closing limit is necessary to turn
the adjusting screw placed on the head of the motor through
the plastic screwdriver included in the box (fig.4).
•
Feed the motor and observe the sense of rotation of the
pulley and/or of the crown ; turn the adjusting screw towards
(+) to increa se the speed of the motor, turn the adjusting
screw towards (-) to decrease it (fig.4).
•
Reverse the direction of revolution of the motor and operate
on the second limit switch (fig.4).
8
of the limit switch
(fig.1).
on the pulley
.
and the washer
Tabla de contenido
