Product Features - V2 VEO Serie Manual Del Usuario

N. PROBLEMS
1 Motor doesn't run
2 Motor runs intermittently
3 Motor does not shut off
4 Motor run only one direction
Warranty
V2 SPA warranties the goods supplied during the sixty months
for motors and 24 months for electronically devices after the
date of manufacturing.
Warranty covers the free repair or replacement of the defective
goods due to a bad manufacturing, according to V2 SPA final
decision.
The goods under warranty shall be sent DDP (Incoterms 2000
CCI) to V2 SPA, and they shall be sent back EX-WORKS
(Incoterms 2000 CCI) to the Buyer.
The replaced material shall be of V2 SPA own. The Buyer shall
pay the labor costs. The Buyer shall not be entitled in any
compensation for any plant outage. The repair/replacement time
shall not extend the warranty period. It is understood that the
warranty shall depend on the specifications of the products,
being duly shown into their operating manuals.
Warranty does not cover as follows
• Any carriage damage or average;
• Any damage caused by any electric plant failures or
negligence, a different use of the system as to its original
purpose and any improper use as well;
• Any damage caused by a staff's tampering or any use of
non-original spare parts;
• Any defect caused by chemical agents or atmospheric
phenomenon;
• Any consumption material;
• Any call for supposed failures or convenient surveys.

Product features

V2 SPA's products are subject to continue changes and
improvements; therefore their technical features and image may
change without a previous notice.
CAUSE
Public electricity supply failure
The switch is defective
Repeated operation may have tripped the
motor overload protector switch
Have the wiring connection between switch and
motor checked by an authorized electrician
To low voltage
Over loading
Bad accessory position
The switch of position limiting of the other
direction is off.
No power of the other direction
WAY
Check with a neighbor
Have it checked by an authorized electrician
Redistribute the load
Wait 15 min and try again
Replace if necessary
To rated power
Choose the relevant load to the rated torque
Check crown/pulley fit perfectly on the tube
Turn the screw limit adjustement on + way
Check the wire connection
EC DECLARATION OF INCORPORATION FOR
PARTLY COMPLETED MACHINERY
(Directive 2006/42/EC, Annex II-B)
The manufacturer V2 Hangzhou Co. Ltd, headquarters in
Building 6, No.12 Kangyuan Rd., Kangqiao District,
Hangzhou, P.R. China
Under its sole responsibility hereby declares that:
the partly completed machinery model(s):
• VEO6-230V, VEO10-230V, VEO6-120V, VEO10-120V
• LEX10-230V, LEX20-230V, LEX30-230V, LEX40-230V
LEX50-230V, LEX20-120V, LEX40-120V
• LEX-H20-230V, LEX-H30-230V, LEX-H40-230V
LEX-H50-230V, LEX-H20-120V, LEX-H40-120V
• ROLL80-230V, ROLL100-230V, ROLL80-120V
• HANDROLL80-230V, HANDROLL100-230V, HANDROLL80-120V
Description:
electromechanical actuator for awnings and
rolling shutters
- is intended to be installed on awnings and rolling shutters
to create a machine according to the provisions of the
Directive 2006/42/EC. The machinery must not be put into
service until the final machinery into which it has to be
incorporated has been declared in conformity with the
provisions of the Directive 2006/42/EC (annex II-A).
- is compliant with the applicable essential safety requirements
of the following Directives:
Machinery Directive 2006/42/EC (annex I, chapter 1)
Low Voltage Directive 2006/95/EC.
Electromagnetic Compatibility Directive 2004/108/EC.
The relevant technical documentation is available at the national
authorities' request after justifiable request to:
V2 S.p.A., Corso Principi di Piemonte 65,
12035, Racconigi (CN), Italy
The person empowered to draw up the declaration and to
provide the technical documentation:
Cosimo De Falco
Legal representative of V2 Hangzhou and V2 S.p.A.
Racconigi, 11th January 2010
9