Important - Pentair SPABRITE Manual Del Propietário

C. To remove light assembly, remove the special pilot screw at top of face ring, remove light assembly from niche, and place
assembly on deck.
Be sure to keep the special pilot screw from this underwater light. This screw mounts and electrically grounds the housing securely
to the mounting ring and wet niche. Failure to use the screw provided could create an electrical hazard which could result in death or
serious injury to pool users, installers or others due to electrical shock.
D. Disassemble light fixture and remove bulb. Remove and discard
old gasket.
E. Install new gasket during reassembly of light, Pentair Water Pool
and Spa part number 79108600.
F. Select the replacement bulb from Table 1.
1. For AquaLight of 100 watt and 250 watt; see Figures 2-3.
2. Squeeze wire form at rounded ends until the wire comes
together and forms a diamond shape opening; see Figures 2-3.
Be careful not to touch bulb with bare skin, as this will reduce the life of the bulb. Use the plastic wrapping of the new bulb, or a cloth
to grasp the bulb.
3. While holding wire form in diamond shape, insert bulb through diamond opening and thread bulb into socket.
Never operate the underwater light for more than 10 seconds unless it is totally submerged in water. Without total submersion, the light
assembly will get extremely hot and may result in serious burns or in breakage of the lamp or lens. This may result in serious injury
to pool users, installers, or bystanders, or in damage to property.
4. With the light resting on its base, place the gasket on top of the light shell. A NEW LENS GASKET MUST BE USED
EACH TIME THE LIGHT IS REASSEMBLED. Locate the word "TOP" on the lens surface. Align the pilot screw
on the face ring with the letter "O" in the word "TOP" and the arrow on the label marked, "Arrow on this label must
line up with the pilot screw on the face ring."
5. The semi-assembled light will now include the face ring and its new gasket properly aligned with the light shell. Place
this light upside down on the old gasket, using the old gasket as an assembly fixture. This will keep the lens and gasket
assembly from being pushed out of the face ring while you secure it to the light fixture.
G. Secure the face ring to the light fixture. Sealing screws must be tightened in the following manner to ensure a proper seal.
1. For lights with chrome or brass face ring:
a. Partly tighten the screw at the 3 o'clock position, and then partly tighten the screw at the 9 o'clock position. Partly
tighten the screw at another 'opposite' position, and then partly tighten the screw directly across from it.
b. Continue partly tightening all screws in the above sequence until all screws are evenly and securely tightened.
Recommended 20 inch pounds torque.
2. For lights with stainless steel face ring:
a. With the bent ends of the circular unitension clamp pointing down
spread the clamp and place it in the "U" recesses of the locking levers.
Ensure that the bent ends of the clamp are located between the pair
of locking levers as shown in Figure 4, location A. Check to see that
the clamp is properly engaged with all of the levers; see Figure 4.
b. Hold the ends of the unitension clamp together. Insert the bolt
through one end of the bend end and then insert the other end through
the other bent end and thread the bolt into the nut. Using a #3 Phillips
head screwdriver tighten the screw and nut until the distance between
the ends of the clamp equals ¼ inch or less, see Figure 5.
P/N • Núm/Pte. • Réf. 99410000
WARNING
Lamp Specifications:
120 volt - 250 watt - T-4 lamp**
120 volt - 100 watt - T-4 lamp**
120 volt - 60 watt - PAR 16 lamp*** *Transformer required
12 volt - 100 watt - R-20 lamp***
12 volt - 75 watt - MR-16 lamp**
** AquaLight - *** SpaBrite
Table 1.

IMPORTANT

WARNING
6
12* volt Models
75 watt
100 watt
120 volt Models
60 watt,100 watt
250 watt
Figure 3.
Figure 2.
Rev. J • Rev. J • Rév. J 5-2-13