Hydraulic connections
The "sauna" model is equipped with an automatic filling tank
which must be powered by a a 1/2" M (cold water) pipe joint (po-
sition 5S).
In order to ensure correct operation, the pressure and flow
rate values must also comply with the values specified in the rel-
evant "Hydraulic specifications".
Where "hard" water is present, it is advisable to install
a decalcifier in the water system supplying water to the
appliance, in order to reduce and/or avoid calcareous
deposits.
ATTENTION: (IEC 60335-1/A2) The pressure of the wa-
ter system supplying water to the appliance must not
exceed 600 k Pa (6 bar).
Electrical connections
The electrical connection can be made in one of the following
ways:
sauna
- single-phase line (220-240V 1~);
- three-phase line consisting of three phase conductors +
neutral conductor (380-415V 3N~).
The rated power supply voltage of the equipment is
always 220-240V.
The equipment can also be installed in countries where
the 220-240V voltage is supplied by a two-phase system. For
the connection please refer to the instruction manual.
Each "sauna" is equipped with a multiple-pole switch, complete
with a cable, approximately 400 cm in length, already connected
to the appliance's junction box, as indicated in position 2S.
This switch must be connected to an area that complies with the
safety regulations as specified by current legislation in force.
Some models allow you to connect the appliance to an alarm
circuit (provided, in the area marked with the bell symbol), a
bipolar cable with characteristics not inferior to type H 05 VV-F
2x2.5 mm
2
(220-240V - 2A max.); this cable must be used in order
to ensure that the cable clamp attached to the box offers ad-
equate protection (water tight) as detailed by legislation.
Audio system
"Sauna" and/or "hammam" are equipped with speakers* that
can be connected to a cable radio network; the relevant cable
must be arranged as indicated in position 3.
Upon request, an audio kit is available, which can be installed in
the appliance's appropriate equipment zone, to which the speak-
ers will also be connected.
NOTE:
(*) two + two speakers; impedance: 8 Ω - optimal power: 20 W x4.
Remote control system arrangement
(where present)
it is possible to manage the "sauna" and "hammam" functions
using a computer which interfaces with a remote control system
(sc) via an Ethernet (LAN) network:
sc
it is also possible yo use a smartphone or tablet computer,
which interfaces via a wireless network (WLAN/Wi-Fi):
sc
sim
In any case, you must use an Ethernet socket (RJ-45), as indicated
in position 8, to which the cable (length: ~ 5 m) coming from the
remote control system, must be connected.
The remote control system (to be installed in the appliance
equipment zone) allows for the management of a maximum of
10 modules (max. 5 saunas and max. 5 hammams).
The cable connecting one module to another must not be longer
than 500 metres (in such a case, you may need to install another re-
mote control system, in order to reduce the length of the cable section).
Thanks to a SIM card, the Sasha remote control system sends,
via short SMS messages, warnings with regards malfunctions to
a specified mobile telephone; the card (not supplied) must be in-
serted to the remote control system during installation.
We advise you check the cover offered by your mobile tele-
phone operator.
NOTE: It is not possible to manage the control system via SMS.
With regards the management and configuration of the connection
network (LAN, WLAN, Wi-Fi, etc..), we recommend that you consult
a technical expert in the subject.
Electrical safety
Sasha is a safe appliance, manufactured according to regulations
EN 60335-1, EN 60335-2-105, EN 60335-2-53, EN 61000, EN
55014-1, EN 55014-2 and tested during production to guaran-
tee user safety.
Installation must be carried out by qualified and authorized
personnel, in compliance with the national provisions in force.
14
LAN
SMS
wi-fi