Disassembly Options/Cleaning; Accessories And Spares; Adaptors; Spare Parts 2.5 Ml, 5 Ml - VWR Zippette Classic Manual De Instrucciones

ZIPPETTE CLASSIC

Disassembly Options/Cleaning

WARNING Do not use force in assembly or disassembly.
Disassembly should only be undertaken after the unit has been cleaned
using the recommended cleaning procedure. Wear protective clothing and
goggles during disassembly.
1. Move the cursor (6) down the scale and undo the dispense sleeve cap (1)
by turning anti-clockwise and lifting.
2. The piston holder (2) is now exposed and the piston (4) is ready for
removal. Remove the piston assembly carefully.
3. Clean the piston's surface with a suitable cleaning solution. Do not
use hard tools to scrape off residue of reagent from the piston as this
will damage the surface and will not seal with the glass barrel when
reassembled.
4. If it is necessary to clean or replace the graduated outer dispense
sleeve (5) of your Zippette Classic, this is carried out with the help of the
supplied assembly tool (17).
a. Loosen the polypropylene threaded ring (9) on the base by
approximately one turn.
b. Using the assembly tool (17), undo the top stop ring (3) by turning
clockwise and lifting it out. You can now lift off the dispense sleeve (5).
c. To remove the polypropylene protection sleeve (11) and borosilicate
glass barrel (10), fully undo the threaded ring (9), remove the
polypropylene protection sleeve (11) and gently lift out the glass barrel
(10) for replacement or cleaning.
Note: Bevelled inside edge of barrel must be at the top
end when fitted.
d. Removal of FEP dispense tube (14); Firstly turn the anti-drip tap to the
closed position. Then remove dispense tube protection cover (15) in an
upward direction allowing dispense tube (14) to be pulled out of anti-
drip shut-off valve assembly in direction indicated on page 7.
e. Reassemble in reverse, make sure the front end of the dispense tube is
clipped into the dispense tube protection cover (15) from the underside.
f. Reassemble the remaining components following the above points in
reverse order, making sure that the FEP 'O' ring (12) is well located into
its platform recess. Take special care not to damage the piston when
inserting it into the glass barrel.
g. Before tightening the threaded ring (9) fully onto the threaded
platform base (13), rotate the polypropylene protection sleeve (11)
so that the tooth on its base locates properly into the notch on the
threaded ring (9).
Spare Parts
Description Drawing EU Cat. No. NA Cat. No. EU Cat. No. NA Cat. No.
Stop Ring 3
Threaded Ring 9
Borosilicate Glass Barrel 10
Protection Sleeve 11
FEP 'O' Ring 12
FEP Dispense Tube 14
Polypropylene Dispense
Tube Protection cover 15
PTFE Inlet Tube 16
Assembly Tool for Outer
Sleeve 17
Pedestal Complete
Assembly 20
Piston Assembly 21
See page 7 for reference
6 vwr.com | Instruction manual
2.5 ml 5 ml
613-5684 10782-832 613-5684
613-5663 10782-852 613-5663
613-5681 10782-826 613-5682
613-5686 10782-836 613-5686
613-5666 10782-786 613-5667
613-5659 10782-790 613-5659
613-5660 10782-794 613-5660
613-5658 10782-772 613-5658
613-5683 10782-830 613-5683
613-5673 10782-808 613-5673
613-5676 10782-816 613-5677
h. After reassembling the instrument, prime with distilled water to ensure
that assembly has been correctly followed and the piston is working
smoothly. Check that no leaks occur.

Accessories and Spares

Adaptors

A range of four adaptors for fitting your dispenser to the reservoir are
available along with an angled funnel to aid filling of reservoirs.
30 mm
33 mm
EU Cat. No. 612-3980
NA Cat. No. 53409-990
30 mm
40 mm
EU Cat. No. 612-3977
NA Cat. No. 53409-994
Description
10782-832 Stop Ring
10782-852 Threaded Ring
10782-828 Borosilicate Glass Barrel
10782-836 Protection Sleeve
10782-788
FEP 'O' Ring
10782-790 FEP Dispense Tube
Polypropylene Dispense
10782-794 Tube Protection cover
10782-772 PTFE Inlet Tube
Assembly Tool for Outer
10782-830 Sleeve
Pedestal Complete
10782-808 Assembly
10782-818 Piston Assembly
See page 7 for reference
EU Cat. No. 612-3978
NA Cat. No. NA 53409-992
EU Cat. No. 612-3979
NA Cat. No. 53409-996
Drawing EU Cat. No. NA Cat. No. EU Cat. No. NA Cat. No.
10 ml
3 613-5684 10782-832
9 613-5663 10782-852
10 613-5689 10782-842
11 613-5686 10782-836
613-5692 10782-848
12
14 613-5659 10782-790
15 613-5660 10782-794
16 613-5658 10782-772
17 613-5683 10782-830
20 613-5673 10782-808
21 613-5678 10782-820
30 mm
38 mm
30 mm
45 mm
30 ml
613-5685 10782-834
613-5663 10782-852
613-5690 10782-844
613-5687 10782-838
613-5693 10782-850
613-5668 10782-792
613-5660 10782-794
613-5658 10782-772
613-5683 10782-830
613-5674 10782-810
613-5679 10782-822