Makita DVC265 Manual De Instrucciones página 18

Troubleshooting for wireless activation function
Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual,
d o not attempt to d ismantle t h e tool. I nstea d , ask Makita A ut h ori z e d S er v i c e C enters, al w a y s using Makita repla c e-
ment parts f or repairs.
State of abnormality
T h e w ireless ac tiv ation lamp d oes
not ligh t/ blink.
Cannot finish tool registration / can-
c elling tool registration suc c essf ully .
Probable cause (malfunction)
T h e w ireless unit is not installed into th e
c leaner and / or th e tool.
T h e w ireless unit is improperly installed
into th e c leaner and / or th e tool.
T h e terminal of th e w ireless unit and / or
th e slot is d irty .
T h e w ireless ac tiv ation button on th e
tool h av e not been push ed .
T h e stand -by sw itc h on th e c leaner is
not set to " I ( O N) " .
No pow er supply
T h e w ireless unit is not installed into th e
c leaner and / or th e tool.
T h e w ireless unit is improperly installed
into th e c leaner and / or th e tool.
T h e terminal of th e w ireless unit and / or
th e slot is d irty .
T h e stand -by sw itc h on th e c leaner is
not set to " I ( O N) " .
No pow er supply
I nc orrec t operation
T h e tool and c leaner are aw ay f rom
eac h oth er ( out of th e transmission
range) .
Before finishing the tool registration/
c anc ellation;
- th e sw itc h trigger on th e tool is pulled
or;
- th e c leaner' s sw itc h to start v ac uuming
is push ed .
T h e tool registration proc ed ures f or
th e tool or th e c leaner h as not been
finished.
R ad io d isturbanc e by oth er applianc es
w h ic h generate h igh -intensity rad io
w av es.
18 ENGLISH
Remedy
I nstall th e w ireless unit c orrec tly .
G ently w ipe of f d ust and d irt on th e terminal of th e
w ireless unit and c lean th e slot of th e c leaner and /
or th e tool.
P ush th e w ireless ac tiv ation button on th e tool
briefly. Make sure that the wireless activation lamp
is blinking in blue.
S et th e stand -by sw itc h on th e c leaner to " I ( O N) " .
S upply th e pow er to th e tool and th e c leaner.
I nstall th e w ireless unit c orrec tly .
G ently w ipe of f d ust and d irt on th e terminal of th e
w ireless unit and c lean th e slot of th e c leaner and /
or th e tool.
S et th e stand -by sw itc h on th e c leaner to " I ( O N) " .
S upply th e pow er to th e tool and th e c leaner.
Push the wireless activation button briefly and
perf orm th e tool registration/ c anc ellation proc ed ures
again.
G et th e tool and th e c leaner c loser to eac h oth er.
T h e max imum transmission d istanc e is approx i-
mately 1 0 m h ow ev er it may v ary ac c ord ing to th e
c irc umstanc es.
Push the wireless activation button briefly and
perf orm th e tool registration/ c anc ellation proc ed ures
again.
P erf orm th e tool registration proc ed ures f or th e tool
and th e c leaner at th e same timing.
Keep th e tool and th e c leaner aw ay f rom th e appli-
anc es suc h as W i-F i d ev ic es and mic row av e ov ens.