Idiomas disponibles
Idiomas disponibles
A
X
1160
895
NOTE: The appliance should be HARD wired to an electrical power
outlet when placed in a recessed installation.
Please consult a qualified electrician for appropriate wiring
requirements.
Manual Operation
The switches are located at the bottom right side of the appliance
see Fig. 6.
Remote Operation
The standby switch (S1) must first be turned 'ON'.
Note: It takes some time for the receiver to respond to the transmitter.
DO NOT PRESS the buttons more than once within two seconds for
correct operation.
Manual & Remote Operation
Setting
Operation
Flame Effect
Press the ' I ' button (Switch 3)
The Standby switch must first be turned 'ON' to operate the appliance
manually or by remote control.
Note: It takes some time for the receiver to respond to the transmitter.
DO NOT PRESS the buttons more than once within two seconds for
correct operation.
To go to the previous settings press the O button.
Pressing the O button on the remote turns off the appliance. To turn
the appliance back On press the I button - see Fig. 8.
To increase or decrease the brightness of the flames, use the dimmer
button or the
button on the Remote Control.
To turn off the power the Standby Switch must be turned 'OFF'.
Lamp Replacement
WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY
BEFORE REMOVING LAMPS.
Warning - The lamps reach high temperatures during operation. For
this reason, allow the lamps to cool down after switching off the
appliance.
The front panel will need to be removed in order to change lamps –
see Fig. 9.
Warning - The front panel is heavy and easily damaged.
The front panel is supported at the top by two brackets and held tight
by magnets at the bottom.
To gain access to lamps please apply the following
procedure:
While holding the front panel by its sides with both hands, (1) carefully
tilt the bottom of the frame outwards until free and then lift the panel
up (2) and then away (3) from the main body - see Fig. 9.
To gain access to the bulbs remove the screws at 'A' to remove the
cover bracket 'X' and the screws at 'B' to remove the cover bracket
'Y' - see Fig. 10.
To access to the bottom bulbs, carefully slide the flexible rotisserie to
one side ensuring that the rubber grommet is not lost - see Fig. 11.
Remove the defective lamp by unscrewing it - see Fig. 11.
Replace with a 60W E14 SES Clear Candle bulb, rotating it. Take care
not to over-tighten the lamp.
Steps for reassembling the appliance
1. Refit the rotisserie making sure that the rubber grommet is carefully
pushed into the slotted hole on the axial bracket.
2. Replace the cover brackets 'X' and 'Y' - see Fig. 10.
3. Replace the front by aligning the slots at top of the front frame
withthe support brackets on the chassis and ensuring it catches
fully on the support brackets.The magnets on the chassis will hold
the front flush to the main body.
TABLE 1
Y
550
Setting
Top Neon
Cleaning
Z
WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY
BEFORE CLEANING THE APPLIANCE.
150
For general cleaning use a soft clean duster – never use abrasive
cleaners. The glass viewing screen should be cleaned carefully
with a soft cloth. DO NOT use proprietary glass cleaners.
Recycling
For electrical products sold within the European Community.
At the end of the electrical products useful life it should not
-
be disposed of with household waste. Please recycle
where facilities exist. Check with your Local Authority or
retailer for recycling advice in your country.
After Sales Service
Should you require after sales service or should you need to purchase
any spares, please contact the retailer from whom the appliance
was purchased or contact the service number relevant to your
country on the warranty card.
Please do not return a faulty product to us in the first instance as this
may result in loss or damage and delay in providing you with a
satisfactory service.
Please retain your receipt as proof of purchase.
UK
